Table of Contents

(A contact) N.O. (A contact) Specifications N.O. (A contact) N.O.

Table of Contents

Working principle A + A A Series CXS 6, 10, 15, 20, 25, 32 Reverse mounting Piston seal A A A R H R H 1. When the piston is retracting, air is exhausted through both A and A until piston seal H passes air passage A. 2. After piston seal H has passed air passage A, air is exhausted only through A.

HRX-OM-Q026

HRX-OM-Q026-V Operation Manual Installation Operation Original Instructions Thermo Chiller HRSH Series HRSH100-A-20HRSH100-A-40HRSH100-A-20-S HRSH150-A-20HRSH150-A-40HRSH150-A-20-S HRSH200-A-20HRSH200-A-40HRSH200-A-20-S HRSH250-A-20HRSH250-A-40HRSH250-A-20-S HRSH300-A-20HRSH300-A-40HRSH100-W-20HRSH100-W-40HRSH100-W-20-S HRSH150-W-20HRSH150-W-40HRSH150-W-20-S HRSH200-W-20HRSH200-W-40HRSH200

AC Servo Motor Driver LECYM/LECYU Series Compatible LEF  Position control, speed control and torque control Power supply voltage (V) LEJ can be used. 200 to 230 VAC 
Control encoder: Absolute 20-bit encoder LEL Motor capacity (W) (Resolution: 10485

3 q u t y u o A !9 r e @0 !0 !2 !5 !6 !4 i A w A-A Component Parts No. Description Material Note No.

15

Note 5) Each value is a guide. Use such value to select a motor capacity.

MB1

7 i o A A' Cylinder tube sectional view A-A' !0 !1 Parts list No. q w e r t y u i o !0 !1 !2 !3 No. !4 !5 !6 !7 !8 !

CNG

If driving a load such as a relay that generates a surge voltage, use a switch with a built-in contact protection circuit or use a contact protection box.

MNB

If driving a load such as a relay that generates a surge voltage, use a switch with a built-in contact protection circuit or use a contact protection box.

Integrated Controller

B A A B B-B In-line motor Component Parts Component Parts (Top/Right/Left side parallel only) No.

HRX-OM-R026

In case of facility having a small installation area (that can not vent the air naturally) Make a forced air exhaust vent on a wall at a high level and an air inlet on a wall at a low level. 3.

Cylinder with Lock

C DA 30 30 30 H A A H H A H W1 T C Symbol: A16 Symbol: A17 Symbol: A18 Symbol: A19 MM AL DA MM 30 30 30 30 MM MM H A H A H A C H A 36 MWB Series Symbol: A20 Symbol: A21 Symbol: A22 Symbol: A23 RD 30 30 MM 30 DA MM 30 DA MM L DB DB C H A T H A T H A B W H A L K Symbol: A24 Symbol: A25 Symbol: A26 Symbol: A27 DA MM DA MM MM MM 30 30 H AL A H L A H AL H AL L K LB K Symbol: A28 Symbol: A29

HRX-OM-W058

Facility having a small installation area (that can not vent the air naturally) Make a forced air exhaust vent on a wall at a high level and an air vent on a wall at a low level.

HRX-OM-M090

Facility having a small installation area (that can not vent the air naturally) Make a forced air exhaust vent on a wall at a high level and an air vent on a wall at a low level.

ø 40, ø 50, ø 63, ø 80, ø 100 Series CLA2 Fine Lock Cylinder Double Acting, Single Rod

B A B A B A B A B A B A B A B A B A B A B 40 10 8 6 4 4 1 5.5 3.5 3.5 0.5 0.5 0 1 0 7 4 2.5 0 4.5 1.5 12 9 50 10 8 6 4 3.5 1.5 5.5 3.5 3 1 0 0 0.5 0 6.5 4.5 2 0 4 2 11.5 9.5 63 12.5 11.5 8.5 7.5 6 5 8 7 5.5 4.5 2.5 1.5 3 2 9 8 4.5 3.5 6.5 5.5 14 13 80 16 14 12 10 9.5 7.5 11.5 9.5 9 7 6 4 6.5 4.5 12.5 10.5 8 6 10 8 17.5 15.5 100 17.5 16.5 13.5 12.5 11 10 13 12 10.5 9.5 7.5 6.5 8 7 14 13 9.5

CM2

Use caution to the popping of a snap ring. When replacing rod seals and removing and mounting a snap ring, use a proper tool (snap ring plier: tool for installing a type C snap ring). Even if a proper tool is used, it is likely to inflict damage to a human body or peripheral equipment, as a snap ring may be flown out of the tip of a plier.

CL

If there is a risk of contact, provide safety measures such as a cover or a system that uses sensors that will activate an emergency stop before contact is made. 2. Use a balance circuit in which lurching of the piston is taken into consideration.

HRX-OM-R016

Facility having a small installation area (that can not vent the air naturally) Make a forced air exhaust vent on a wall at a high level and an air vent on a wall at a low level.

HRX-OM-R005

Facility having a small installation area (that can not vent the air naturally) Make a forced air exhaust vent on a wall at a high level and an air vent on a wall at a low level.

HRX-OM-W038

Facility having a small installation area (that can not vent the air naturally) Make a forced air exhaust vent on a wall at a high level and an air vent on a wall at a low level.

HRX-OM-X027

Facility having a small installation area (that can not vent the air naturally) Make a forced air exhaust vent on a wall at a high level and an air vent on a wall at a low level.