Heatless Air Dryer Series ID 1 (Inlet air pressure: 0.7 MPa, Inlet air temperature: 20C) HA How to Order AT ID 20 02 0 ID AMG ID400 Option B Bracket Z Adsorbent for low dew point Basic size AFF 20 30 40 60 Port size AM ID200 02 B 04 06 1 4 B 1 2 B 3 4 Nil Rc Thread type Misc.
To ensure safety, be sure to observe ISO 4414 Note 1), JIS B 8370 Note 2) and other safety practices. Caution : Operator error could result in injury or equipment damage.
CDA2 B 50 200 X1184 B31J S With built-in special magnet Number of auto switches Cylinder stroke Description 2 pcs. 1 pc.
POINT POINT POINT POINT When heating the circulating fluid, the high-pressure, high-temperature refrigerant gas is bypassed into the evaporator by expansion valve B to heat the circulating fluid.
WQ Edition B Safety Instructions Be sure to read the Handling Precautions for SMC Products (M-E03-3) and Operation Manual before use.
(b) Moisture in the refrigerant circuit (colour of the indicator) Green (DRY) ---Good Yellow (WET) ---Moisture is present in the refrigerant.
When it is connected to GND , channel B is selected.
Store in an area that is shaded from direct sunlight and has a temperature and humidity within the specified range (10C to 60C and 35 to 85% no condensation or freezing). 3. Do not apply vibration or impact to the product during storage. 2.6 Maintenance Warning 1. Do not disassemble or repair the product. Fire or electric shock can result.
side Voltage 3 110VDC 5 24VDC Manual override B Locking type (Tool required) Thread type N NPT Thread size 02 1/4 Specifications 5-way solenoid valve configuration (for Double acting actuator ) Fluid Air or inert gas Reverse function Normal function Working pressure range 21.8psi to 130psi (0.15 to 0.9 MPa) D-TYPE B-TYPE Ambient & Fluid Temperature 14F to 140F (10C to +60C) Lubrication Not
Series VXF Model Selection (In the case of using as a bag filter) Model selection The deterrioration of VXF/VXFA properties due to the tube length from data B (response time/idle time) and data C (start-up speed), can be measured. Refer to this data to set energization time.
Non-locking push type [Standard type] Locking slotted type [B] Crimping area Core wire contact area Turn in the direction of arrow.
AMG Color of indicator Dew point temperature (Atmospheric pressure) 30C or less 18C 10C Dark blue Light blue Light pink Conditions/Inlet air pressure 0.7 MPa Inlet air temperature 30C Please use the adsorbent set (refer to page 134 for Accessory/ Replacement Parts) when replacing the adsorbent. AFF Piping Caution AM AMD 1.
CXSJ10 / CXSJ10 11122122Note 2) D B Note 3) (mm) D-M9 34 (35.5) 3.5 (2) 24 (25.5) 6.5 (8) D-A93 30 (31.5) 25.5 (27) 5 (6.5) Symbol A B C D Note 1) The above mentioned values are indicated as a guide for auto switch mounting positions for stroke end detection. When actually mounting an auto switch, adjust the position after confirming the operating state of the auto switch.
: inch (mm) 10mm N 3/8 B Q E D A G C F 1 J 31.5 [820] P L K M N H (L=2800) IDFB4E/6E/8E/11E-11 1. : inch (mm) 10mm N 3/8 A B E D Q G C F 1 J 31.5[800] H N M 4-0.5 (L=2800) [4-13] 6-3 6 3 IDFB Series IDX-OM-W020 6 IDFB15E-11 1. : inch (mm) 10mm N 3/8 E D B A Q G C F (820) K L P N M H J 4-13 (L=2800) (inch [mm]) A B C D E F G H J K L M N P Q IDFB3E 3/8 8.9 16.1 18.6
In particular, if three or more adjacent stations on the manifold are energized simultaneously for extended periods of time or if the valves on A side and B side are energized simultaneously for long periods of time, take special care as the temperature rise will be greater.
Please check each application as the surface temperature is application dependent. *3 2-port (SX91/92): Based on dynamic performance test, JIS B 8373. (Coil temperature: 20C, at rated voltage) 3-port (SX090) : Based on dynamic performance test, JIS B 8419.
Slide Unit/Double Rod Type Series CX2 Slide Bearing: 10, 15, 25 How to Order Port thread type Symbol Bore size 10, 15 Type M thread Rc 1/8 NPT 1/8 G 1/8 Nil TN TF 25 CX2 N 15 100 B C X2 N 15 B 100 J79W DB With auto switch Made to Order Cylinder with auto switch Refer to page 465 for Made to Order specifications.
Furthermore, when using at low friction, it is also recommended to use clean air (atmospheric pressure dew point temperature of 10C) and install mist separator series AM (filtration degree 0.3 micron or less) or series AM + AMD (filtration degree 0.01 micron or less). 3. Install an after-cooler, air dryer or water separator, etc.
class B Flow characteristics Flow characteristics Max. operating pressure C[dm3/(sbar)] Power consumption b Cv 0.5MPa 0.27 0.042 0.011 0.5WDC 0.3MPa 0.28 0.083 0.021 0.3MPa 0.27 0.042 0.011 0.35WDC 0.1MPa 0.28 0.083 0.021 0.3MPa 0.27 0.021 0.006 0.1WDC with power saving circuit(Holding) 0.35WDC(Inrush) 0.1MPa 0.28 0.042 0.011
Note 2) JIS B 8370 : Pneumatic system axiom. Warning 1. The compatibility of pneumatic equipment is the responsibility of the person who designs the pneumatic system or decides its specifications.