LEC-OM032xx

Communication is interrupted. 5. 4 CN2: PC/TB connector The connector which connects the tools teaching box (LEC-T1-3*G*) or PC (LEC-W2) for setting the controller (LEC.

JXCx-OMT0028CN

-3G)(LEC-W2)(CN2SW)OFF (LEC-T1-3G)(LEC-W2) TB/PC (CN2) LED CN2 SW CN2STAT BUS STAT OFF (1) GW CN2 3m LEC-T1-3G (2) LEC-W2 USB CD GW 120.3 120.3 mm mm 200 200 mm/s mm/s USB 100 500 100 500 1 1 200 1000 200 1000 2 2 A-miniB type 50 200 50 200 3 3 CN2 CN2TB/PC 27 - 6.CN4 6.1 No.

VQ5000

IP65 compatible T1 S kit (With individual terminal blocks) kit (Serial transmission) Use as a guide for selection. Please confirm the actual conditions with SMC Sizing Program.

SY

(Max. 20 stations) Applies to 45T/T1 only. 24VDC only for type S.

Electric Grippers

Option Teaching box Controller setting software Page 82 Page 81 (With 3 m cable) Part no.: LEC-T1-3JG Communication cable (With conversion unit) and USB cable are included.

HRX-OM-W004

Silent interval is indicated by T1-T2-T3-T4. Table 3.8.2 RTU mode message frame a)Start b)Slave Address c)Function d)Data e) Checksum (CRC) f)End T1-T2-T3-T4 XX XX XX XX XX XX T1-T2-T3-T4 a) Start In Modbus RTU mode, message frames are separated by a silent interval (non-communication time).

Electric Actuator High Rigidity and High Precision Slider Type Circular arc grooves allow for high rigidity and high precision. Moment resistance*1 *2 61% Improved by up to Table displacement*1 50% Reduced by up to With internal battery-less absolute e

Calculation example) T1 to T4 can be calculated as follows. L Speed: V [mm/s] a1 a2 T1 = V/a1 = 300/3000 = 0.1 [s], T3 = V/a2 = 300/3000 = 0.1 [s] Time T = T1 + T2 + T3 + T4 [s] [s] L 0.5 V (T1 + T3) V T1: Acceleration time and T3: Deceleration time can be found by the following equation.

Environment

L Speed: V [mm/s] Cycle time T can be found from the following equation. a1 a2 T = T1 + T2 + T3 + T4 [s] T1: Acceleration time and T3: Deceleration time can be obtained by the following equation. Time [s] T1 = V/a1 [s] T3 = V/a2 [s] T1 T2 T3 T4 T2: Constant speed time can be found from the following equation.

(between live parts and case)50 M or more (at 500 VDC by megameter) between live parts and case01: R 1/8, M5 x 0.8 T1: NPTF 1/8, M5 x 0.80X: With suction filter (For mounting on ZX unit) 0R: Base mount type (For mounting on ZR unit)35 g (Including 0.6 m-Long lead wire)Oil-resistant vinyl cabtire code 3 cores, ?

Plug-in/Plug Lead: Single Unit

Note 3) Available only with F , L and T1 kits. Note 4) Specify the wiring specifications on the manifold specification sheet. (Except L kit) . . . . . . Minimum number of stations depends on the kit. (Refer to the table below.)

Thermo-chiller

[W] = 7.3 [kW] T = T2 T1 Cooling capacity = Considering a safety factor of 20%, 7.3 [kW] x 1.2 = 8.8 [kW] T1: Outlet temperature 23 Cooing Capacity Calculation Series HRS100/150 Required Cooling Capacity Calculation Example 3: When there is no heat generation, and when cooling the object below a certain temperature and period of time.

5 Port Solenoid Valve Series SY3000/5000/7000/9000

Mark: 45T and T1 only S type is available for 24 VDC only. Nil CE-compliant CE-compliant X90 Main valve fluoro rubber (Refer to page 332.)

Series SY 5 Port Rubber Seal Solenoid Valve High Capacity & Simple Choices

(Max. 20 stations) Note) Indicate "Nil" for types T, T1, and S.

Vacuum Manifold for fieldbus system

Pneumatic Circuit Standard products (No Option) Single unit: ZKJ-E5U-T1 Single unit: ZKJ-A5U-T1 With manual override With exhaust sealing valve High-noise reduction silencer exhaust High-noise reduction silencer exhaust Port exhaust Port exhaust Supply valve: N.O. Release valve: N.C. Supply valve: N.C.

MONOSASHI-KUN WITH BRAKE CONTROLLER

to origin)s signal, if sensor does not receive any signal within t1 (situation whereby the cylinder stops), this reflects homing is achieved.

CEx-OMG0106

If sensor does not receive any signal within t1 (situation whereby the cylinder stops), this reflects homing is not achieved. Setting of response time should take into consideration of load, mounting condition, tubing length, etc. The response time should be re-calibrated, if the operating conditions change.

LEC-OM005xx

LEC-OM00506 PRODUCT NAME Teaching Box for Electric actuator MODEL / Series/Product Number LEC-T1 Series Applicable models For Series LEC For Series LEC For Series LECPA (TB Ver2.1 or more) Contents Safety Instructions . 6 Changes by teaching box version. . 8 1.

Table of Contents

Power supply 11) 100/110V AC (50/60Hz) 200/220V AC (50/60Hz) 21) 1) Consult SMC if the supply voltage for LC1-1HV1 will be 110V AC or more, or the supply voltage for LC1-1HV2 will be 220V AC or more. or LC1-1-T1(Teaching box) are required.

Table of Contents

bar absolute, T1 = 297 5K, 0.07 bar P 0.14 bar.

45

Connector block assembly (For 9 to 17 stations (T1) terminal block) t-6 SX5000-64-8A SX3000-64-8A M3 x 30 (Matt nickel plated) SX3000-22-2 (M2 x 24) SX5000-57-6 Round head combination screw y Gasket DIN rail SX3000-57-4 VZ1000-11-1u i Refer to page 1-6-77. Note) The numbers t1 to 4 are for 24 VDC. For 12 VDC, suffix -12V to the parts no.