AR20-B to AR60-B When the inlet pressure is shut off and exhausted, any inlet pressure applied to the valve q will be lost. The force for seating the valve q is the valve spring force w only. When the valve q is opened using the outlet force, the outlet pressure will be exhausted at the inlet side (Figure 2).
Cannot be used with M: Round pressure gauge (with color zone). Available by request for special.
Since two valves are installed per manifold base, it must be an even number, so the number of valve that can be installed is 08. Specify four (4) stations for manifold Specify when the gate valve is necessary for cleaning valve. This example requires one gate valve and four cleaning valves, but specify 06 for number of valves that can be installed, as this must be an even number.
Polyurethane tubing: Series TU, Nylon tubing: Series T, and Soft nylon tubing: Series TS can also be used. However, the degree of clean performance will be reduced.
It must be operated manually. 0.2 0.2 0.1 0.1 00 25 50 75 100 125 150 00 1000 2000 3000 Flow rate L/min (ANR) Flow rate L/min (ANR) AR20 Rc 1/4 AR40-06 Rc 3/8 0.6 0.6 0.5 0.5 Outlet pressure MPa Outlet pressure MPa 0.4 0.4 0.3 0.3 0.2 0.2 Caution 1. Be sure to unlock the knob before adjusting the pressure and lock it after setting the pressure.
Polyurethane tubing: Series TU, Nylon tubing: Series T, and Soft nylon tubing: Series TS can also be used. However, the degree of clean performance will be reduced.
Polyurethane tubing: Series TU, Nylon tubing: Series T, and Soft nylon tubing: Series TS can also be used. However, the degree of clean performance will be reduced.
Load factor: ((Load weight x 9.8)/Theoretical force) x 100% Conditions Series CJ2 Series CM2 6 x 1 m AS3301F-06 12 x 1 m AS4001F-12 AN200-02 AS2301F-06 AN110-01 Series MB/CA2 Series CJ2 Series CM2 Series MB/CA2 Body ported Tubing bore x Length Speed controller Silencer Base mounted Tubing bore x Length Speed controller Silencer AN200-02 AN3301F-06 AS1301F-06 6 x 1 m AS3001F-06 SYJ7120-01
-01-06-X214 AS2001F-06-X214 AS2301F-01-06-X214 DREC32 AS2201F-01-06-X214 AS3001F-08-X214 AS2301F-01-06-X214 REC40 AS3201F-02-08-X214 AS3001F-08-X214 AS3301F-02-08-X214 -X Use the recommended speed controllers.
-01-06-X214 AS2001F-06-X214 AS2301F-01-06-X214 DREC32 AS2201F-01-06-X214 AS3001F-08-X214 AS2301F-01-06-X214 REC40 AS3201F-02-08-X214 AS3001F-08-X214 AS3301F-02-08-X214 -X Use the recommended speed controllers.
Also, the surge pressure must be under the maximum operating pressure.
Note 2) On the AMC220, an R 1/4 fittinng can be attached by removing the drain cock. (It be comes the drain piping type.
10-ASD330F-01-08 10-ASD230F-M5-06 2.
If multi-pads are used with only one ejector and one pad does not make complete adsorption, then vacuum pressure will be lost. Subsequently other pads will be unable to complete adsorption.
The load must be guided by other means. The mounting fittings for the load should be designed to meet the weight limits shown in this table.
8, and can be ordered by using the seal kit number corresponding to each bore size.
The OUT direction can be mounted up to 90 to the left or right.
06 FH440-08 FH440-10 FH440-12 FH640-03 FH640-04 FH640-06 FH640-08 FH640-10 FH640-12 3/8 3/8 10 10 FH441-04 FH441-06 FH441-08 FH441-10 FH441-12 FH441-16 FH441-20 FH441-24 FH641-04 FH641-06 FH641-08 FH641-10 FH641-12 FH641-16 15 (1/2B) 15 (1/2B) 1/2 1/2 20 20 20 (3/4B) 20 (3/4B) 3/4 3/4 50 50 Max. 21 MPa 25 (1B) 25 (1B) 1 1 80 80 Max. 7 MPa 32 (1 1/4B) 32 (1 1/4B) 1 1/4 1 1/4 120 120 40