LOCK UP VALVE 3-PORTS Warning Environment (1) Do not use in environment where the product is exposed to corrosive gas, chemicals, salt water, water or steam. (2) Do not operate the product in a location where it is subject to strong vibration and/or shock. For vibration, it should be within 1G 60Hz. ! ! ! ! -6- 7. Maintenance Warning (1) If handled improperly, compressed air can be dangerous.
Warning Environment (1) Do not use in environment where the product is exposed to corrosive gas, chemicals, salt water, water or steam. (2) Do not operate the product in a location where it is subject to strong vibration and/or shock. For vibration, it should be within 1G 60Hz. ! ! ! ! -6- 7. Maintenance Warning (1) If handled improperly, compressed air can be dangerous.
Note 3) The accessory must do the installation work by the customer oneself. HAA Series 4 1. Specifications ATX-OM-F004E Air-Cooled Aftercooler 2. Model No. Identification Mark 2Model No.
Do not apply excessive force or impact. This will not only damage the product but also decrease its performance and life expectancy. It is not possible to disassemble the bonnet assembly of this product. If the components and assembly are damaged, or damage is expected, exchange the bonnet assembly itself. Do not disassemble the parts that are not explained in this operation manual.
Do not apply excessive force or impact. This will not only damage the product but also decrease its performance and life expectancy. It is not possible to disassemble the bonnet assembly of this product. If the components and assembly are damaged, or damage is expected, exchange the bonnet assembly itself. Do not disassemble the parts that are not explained in this operation manual.
M5 x 0.8 (Finger opening port) D3 O 20S 13 3 23 7 M5 x 0.8 (Finger closing port) 4 2 MHY2-10D2 Opening/Closing direction through-hole type 4-3.4 (Hole for mounting attachment) 6 0.005 0.025 3 6 12 (Limted area for mounting attachment) Do not extend the attachment from limited area for mounting to avoid interference with the attachment or main body. 12-10-11 11 Series MHY2 Dimensions MHY2
Do not scratch or gouge the escapement by dropping or bumping it when mounting. Even a slight deformation can cause inaccuracy or malfunction. 2. Please observe the specified torque limits when tightening screws to mount the attachment.
M5 x 0.8 (Finger opening port) D3 O 20S 13 3 23 7 M5 x 0.8 (Finger closing port) 4 2 MHY2-10D2 Opening/Closing direction through-hole type 4-3.4 (Hole for mounting attachment) 6 0.005 0.025 3 6 12 (Limted area for mounting attachment) Do not extend the attachment from limited area for mounting to avoid interference with the attachment or main body. 12-10-11 11 Series MHY2 Dimensions MHY2
If the tubing is inserted without holding the elbow, excessive force can be applied to the valve and fitting assembly, causing air leakage or damage, etc. 1) Nylon tubing within 0.1 mm 2) Soft nylon tubing within 0.1 mm 3) Polyurethane tubing within +0.15 mm, within 0.2 mm Do not use tubes which do not meet these outside diameter tolerances.
When mounting the load with screws, do not exceed the maximum tightening torque. (The torque may vary depending on the material of the load.) Bolt Model Maximum tightening torque (Nm) Caution MGJ6 M2.5 x 0.45 0.5 MGJ10 M3 x 0.5 1.0 1. Do not scratch or dent the sliding parts of the piston rod and guide rods. Damage to seals can cause air leakage or malfunction, etc. 2.
Mounting from upper side l l Model Bolt Maximum tightening torque (Nm) l (mm) MGF 40 MGF 63 MGF100 M6 x 1 10 7.5 M8 x 1.25 25 9 M10 x 1.5 51 9 Mounting from bottom side Do not bring objects that are sensitive to magnetism near the cylinder. There is a magnetic built into the cylinder. Do not bring magnetic disks, cards, or tapes near the cylinder. Data may be lost.
Standard Stroke Do not use the product as a stopper. Do not disassemble and modify the product.
Do not scratch or gouge the escapement by dropping or bumping it when mounting. Even a slight deformation can cause inaccuracy or malfunction. 2. Please observe the specified torque limits when tightening screws to mount the attachment.
Do not exceed the screw-in torque of 3.5 Nm when installing piping. Exceeding this value may cause malfunctioning of the sensor. 4. The minimum bending radius of the cable is 50 mm. 5. Do not use pressure sensors with corrosive and/or inflammable gases or liquids. 1. Incorrect wiring can damage the switch and cause a malfunction or erroneous switch output.
Do not use with pressure or temperature beyond the specification range.
;(E a Slip exceeding retaining force may damage brake shoe, which could lead to reduced relaining force, resulting in its shorter lile a Cylinder loading should be within 35'/" of holding force when the brake is used for droo oroteclion, a Do not apply any impact when you load the cylinder in the locked position.
Do not mark or damage lhe piston rod. This could cause damage to packing and resull in lluid 'eakage. O Do not apply oil lo the sliding section of lhe piston rod, O Do nol apply rclary torque. O Do not apply large-load energy to the model wilh a shock absober when ths shock absolbet is absorbrng enrgy twhen the levt is uprighl).
. * Options are shipped together with the product but do not come assembled. 9 2-Color Display Digital Flow Switch RoHS PF2M7-L Series How to Order Integrated display Made to order (Refer to page 26.)
Do not use in locations having an explosive atmosphere. 2. When vibration or impact is applied, make sure to test in the 2.
Do not supply lubrication, as this is a non-lube product. The interior of the cylinder is lubricated at the factory, and lubrication with turbine oil, etc., will not satisfy the product's specifications. 6. Never reapply lubricant. Never reapply lubricant, as there may be a degradation of particulate generation or operation characteristics. 2.