AMR3000 to 6000 G36-10-01) indicates thread. Specify no symbol for Rc, and N for NPT. Please consult with SMC if NPT gauge is required. Note 6) Use caution not to tighten excessively when mounting a pressure gauge, otherwise it may result in a breakdown. Use a pipe tape for sealing.
Metric sizes Type 04 06 08 10 12 4 6 8 10 12 2 Elbow Control type 0 1 Meter-out Meter-in Port size M5 01 02 03 04 M5 x 0.8 1/8 1/4 3/8 1/2 With One-touch fitting Clean specifications Metal parts material Q G Brass (electoless nickel plated) Stainless steel 304 Needle Valve/Flow Characteristics AS121FP-M5 AS221FP-01 AS221FP-02 08,10 06,08 06 04 04 AS321FP-03 AS421FP-04 12 10 10,12 08 06 15
IZN10 IZN10 IZN10 IZN10 01 01 01 01 P P P P 06 06 06 06 Z Z Z Z B1 B1 B1 B1 IZN10 AC 01 02 11 Rc1/8 NPN P PNP 06 6 07 6.351/4) 16 6 ( 17 6.351/4() (3m) Z (10m) N IZN10-NT L DIN IZN10A002 IZN10B1 L B2 B3 DIN 01 06 ES 2 01 ES 17mm 2 2 02 3 3 11 Rc1/8 4 4 /IZS30 /IZS30 /IZS30 /IZS30-M2 M2 M2 M2 06 6: 07 6.351/4: 16 6 :( 17 6.35(1/4):() IZN10-CP(3m) IZN10-CPZ(10m) IZN10A003 NPN
B IN OUT Model Port size D C B A 30 30 23.5 14 M5 x 0.8 SRP111-M5 40 40 22.5 15 Rc 1/8 SRP111-01 C D 3
A valve, which might potentially cause a hum or buzz can be very annoying to a patient, so a full wave rectified unit for AC service is often preferred. A DC unit, not requiring a rectifier, is sometimes used in specific applications. Also common is a bumper in a 2-way valve, usually just a flat disk with no sealing action.
B A HS 056 HS B A B A 075, 106 HS B A B A 150, 200, 250 Note 1) Figures in the table below are references for auto switch mounting positions in the stroke end detection.
Modular Type Regulator AR Series AC-A Regulator AR Series AF-A Model Port size Options AF-A AR10-A M5 x 0.8 AR-A AR-A AL-A AR20-A 1/8, 1/4 AW-A Bracket AC-B AF-A AR25-A AF-A 1/4, 3/8 Round type pressure gauge AR -A -B AR30-A AL-A Set nut (for panel mount)* AW -A -B AR40-A 1/4, 3/8, 1/2 AW AG AR40-06-A 3/4 * For AR20-A to AR40-06-A, panel fitting dimensions are different from those of the
When a load, such as a relay or solenoid valve, which generates surge is directly driven, use a type of switch with a built-in surge absorbing element. 8.
This chapter has been formulated to have a description of the Function Block, a diagram of the Function Block as seen on the LCD Display, and a logic table to show how the Output is controlled by the input signals. An Input that is ON (or High) is shown as a 1 while an input that is OFF (or Low) is shown by a 0.
[Check valve] A check valve is a safety device intended to prevent reverse flow. The AP 64 is a unique design with only one moving part in the gas stream, an O-ring. It is a springless design, free of springs and poppets. [Vacuum generator] A venturi device that creates vacuum by flowing gas through a nozzle.
When a surge generating a load such as a relay or solenoid is directly driven, use a type of switch with a built-in surge absorbing element. 4. Since the type of fluid varies depending on the product, be sure to verify the specifications. The switches do not have an explosion proof rating. To prevent a possible fire hazard, do not use with flammable gases or fluids. 5.
When a surge generating a load such as a relay or solenoid is directly driven, use a type of switch with a built-in surge absorbing element. 4. Since the type of fluid varies depending on the product, be sure to verify the specifications. The switches do not have an explosion proof rating. To prevent a possible fire hazard, do not use with flammable gases or fluids. 5.
The dual type speed controller is especially suitable for cylinders with a small bore size. Elbow/Universal Type Air Flow/Effective Area Model AS121FM-M5 AS131FM-M5 AS221FM-01 AS231FM-01 AS221FM-02 AS231FM-02 RE A B 3.2, 4, 6 3.2, 4 6, 8 4 6 8, 10 Metric size Tubing O.D.
The dual type speed controller is especially suitable for cylinders with a small bore size. Elbow/Universal Type Air Flow/Effective Area Model AS121FM-M5 AS131FM-M5 AS221FM-01 AS231FM-01 AS221FM-02 AS231FM-02 RE A B 3.2, 4, 6 3.2, 4 6, 8 4 6 8, 10 Metric size Tubing O.D.
2 OUT A IN OUT t BLEED A-A w y Note Component Parts Material No.
2 OUT A IN OUT t BLEED A-A w y Note Component Parts Material No.
To release residual pressure, select a model with a backflow function. Using a model without a backflow function makes for inconsistent residual pressure release (i.e., residual pressure may or may not be released) depending upon the operating conditions. 3.
To release residual pressure, select a model with a backflow function. Using a model without a backflow function makes for inconsistent residual pressure release (i.e., residual pressure may or may not be released) depending upon the operating conditions. 3.
The cylinder should be operated using a connection method which allows for shaft alignment variations and deflection due to the cylinder's own weight. A drawing of a recommended mounting method is shown in Figure 1.
Note 5) Without a valve function.