Vacuum Pad: Ball Joint Type Series ZPT/ZPR Pad Diameter: ø10, ø13, ø16, ø20, ø25, ø32, ø40, ø50 1 Note that sometimes a load is applied to the buffer by a piping tube (pulling or pressing, etc. in a lateral direction). 5. Do not apply an impact or large force to a pad when adsorbing a workpiece. This will cause deformation, cracking and wear of the pad to be accelerated. The stiffening ribs, etc. should touch lightly, while staying within the pad skirts deformation range.
Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Caution: Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Warning: Danger : Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury.
2 OUT A IN OUT t BLEED A-A w y Note Component Parts Material No.
2 OUT A IN OUT t BLEED A-A w y Note Component Parts Material No.
Process Pump (Diaphragm Pump) PB Series Compact, large capacity diaphragm pump, suitable for transferring and collecting a wide range of fluids Compact, large capacity diaphragm pump, suitable for transferring and collecting a wide range of fluids o t p m s l a i PA z P e Built-in solenoid valve only RoHS Smaller, lighter, 25% reduction in volume Smaller, lighter, 25% reduction in volume
0 t i y o Length of plug connector lead wire Description No. Material Component Parts The standard length of the plug connector with a lead wire is 300 mm, but other lengths are available as follows.
A One-touch fitting for 12 is attached to each port.
In terms of voltage, a 5% tolerance is allowed. The dryer comes with a mains connecting cable already installed and ending with a VDE 16A Shucko plug. The mains socket must be provided with a mains magneto-thermal differential breaker (In=0.03A), adjusted on the basis of the consumption of the dryer (see the nominal values on the data plate of the dryer).
Both of these become slower as the operating pressure is increased. 14 Technical Data 5 He leakage 8 Exhaust time (low/medium vacuum) The time (t) required to exhaust a chamber at low vacuum with volume V (l), from pressure P1 to P2, using a pump with pumping speed S (l/sec) is t=2.3(V/S)log(P1/P2).
A MPa ON kPa OUT1 Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com OFF OUT2 CH 1 2 3 4 PRESSURE Min. B Released SET Work 1 Work 2 Work n Atmosphere Max. A: Maximum pressure value when workpiece is adsorbed. A B 4 ON = A A B 4 SET OFF = B + Min.
Lamp Load 0.125 A / 24V DC (3.0 W) Max.
When a workpiece could be deformed during adsorption or transportion. (Example of a cardboard box) When the adsorption surface of a workpiece is slanted.
Therefore, supply pressure regulated by a built-in regulator e passes through the air supply solenoid valve q and is applied to the pilot chamber r. The pressure in the pilot chamber r increases and operates on the upper surface of the diaphragm t. As a result, the air supply valve y linked to the diaphragm t opens, and a portion of the supply pressure becomes output pressure.
36 1/8 (EA, EB port) 1741 Series SYA3000/5000/7000 Dimensions/Series SYA7000: Base Mounted 3/8, 1/4 (A, B port) 21 22.5 2 position single 11.5 13.5 SYA714002 03 57 77.5 42 10.4 61 M5 x 0.8 (Pilot port) B A PE 38 46 B A Manual override P EB EA 21 69 6.4 2 x 4.3 (For mounting) 87.5 26.5 1.8 (Ventilation hole) 13.5 3/8, 1/4 (P , EA, EB port) 20.5 20.5 33 3/8, 1/4 (A, B port) 21 22.5 2 position
0 e New PFA q Body New PFA w Sensor Super PFA e Tube PPS r Housing A PPS t Housing B PPS y Housing C POM u Bushing PPS i Cap FKM o Gasket FKM !0 O-ring Stainless steel 304 !1 Thread PVC !2 Lead wire !1 q t i PF2D540 o !0 u !0 !2ywr e !
The cylinder should be operated using a connection method which allows for shaft alignment variations and deflection due to the cylinder's own weight. A drawing of a recommended mounting method is shown in Figure 1.
Solenoid direction Port size Opposite side of A port Nil 1 8 Rc G NPT NPTF 01 Rc Nil C4 4 cassette F N T Same side of A port S C6 6 cassette P port: Rc 1/8 R port: Rc 1/8 A port: Rc 1/8 Valve stations Type S42 (Solenoids on the same side of A port) 01 1 station CE-compliant VV061 20 20 stations Q CE-compliant Nil P port: Rc 1/8 R port: Rc 1/8 VV100 Note) Applicable only for DIN terminal
1 Fine Lock Cylinder with Guide Series MLGC 20, 25, 32, 40 A linear transfer cylinder unit with a built-in locking mechanism and a guide rod integrated in a compact design.
1 Fine Lock Cylinder with Guide Series MLGC 20, 25, 32, 40 A linear transfer cylinder unit with a built-in locking mechanism and a guide rod integrated in a compact design. CL CL1 MLGC CNG MNB CNA CNS CLS CLQ MLGP RLQ MLU ML1C High level of stopping accuracy D-X Locking method Spring locking Pneumatic locking Spring and pneumatic locking 20Locking in both directions is possible.