A_HEC-OM-K001 M O D E N o r m a l Function
If there is a risk of contact, provide safety measures such as a cover or a system that uses sensors that will activate an emergency stop before contact is made. 2. Use a balance circuit in which lurching of the piston is taken into consideration.
Put a flat washer (8 x 3.3) through a hexagon socket head screw (with spring washer, M3 x 0.5 x 5 l) and passing through the hole of a switch mounting bracket, then turning it lightly down to a mounting nut of switch. (2 locations) 5.
Hs D-G39/K39 D-A3 34 56 56 A A 36 49 Auto switch G 1/2 (applicable cable O.D. 6.8 to 11.5) Approx.
CHAWL CHQ CHK CHN H + Stroke H K F T T V V 2 x Rc P 4 x J GA F GA A MA a CHM A MA a Cushion adjustment screw Air release R (max.)
12.5 ([5m ] (a) (b) L E C P * B -* A B-1 2 A A-1 1 L B B-2 6 B A-2 5 1 1.5m COM-A/COM B-3 3 3 3m COM-B/ A-3 4 (c) 5 5m Shield Vcc B-4 12 GND A-4 13 A B-5 7 A A-5 6 B B-6 9 B A-6 8 3 (d) S 4 + B-1 5 A-1 1 + B-3 2 A-3 (8) (a) (b) (14.2) B1 A1 (17.7) 2 1 (14) (18) 6 (10.2) B6 5 A6 2 1 B1 A1 B3 A3 (d) (5.7) 15 16 (c) L (11) (30.7) 12.6 ([820m] (a) (b) LE CP * B A B-1
5 7 2 5 3 2 2 3 5 3 1 MHZ2-16 No setting 3 2 4 1 MHZ2-20 MHZ2-25 MHZJ2-10 No setting No setting MHZJ2-16 No setting No setting 3 2 1 MHZJ2-20 MHZJ2-25 Note) "" in the table indicates a skip with no dimension.
Although the body of the switch may not be damaged, the inside of the switch could be damaged and cause a malfunction. 2. Do not carry a cylinder by the auto switch lead wires. Broken lead wires will result from applying bending stress or stretching force to the lead wires. 2.
Indication Item Signal type Setting and selection * A contact (normally open) (1) Output 1 Contact output signal 1 Operation status signal B contact (normally closed) A contact (normally open) Operation stop (FLT) alarm status signal (2) Output 2 Contact output signal 2 * B contact (normally closed) A contact (normally open) Continuous operation WRN alarm status signal (3) Output 3 Contact
Circuit (Class 2) of maximum 30 Vrms (42.4 V peak) or less, with UL1310 Class 2 power supply unit or UL1585 Class 2 transformer. The product is a UL approved product only if it has a mark on the body. Use the specified voltage. Otherwise failure or malfunction can result. Insufficient supply voltage may not drive a load due to a voltage drop inside the product.
Torque R1/2: 28 to 30Nm 2) Hold the ball valve with the spanner. Then install a nipple and a motor type auto drain. Install with out port" down in a vertical position.
filter, bypass valve or retaining clip 1 kg*2 -Z1 Without either a flow sensor or retaining clip Not changed *2 Excludes the HRR010.
Analog output 2 1 Signal the contents of the contact output 1 to 3 is a fixed value.
Proper use of the seal cap enables the enclosure to achieve IP67 specification. 25 EX## OMS1015-A Specification Specifications Model EX600-ED2EX600-ED3Power connector M12 (5 pin) Plug 7/8 inch (5 pin) Plug specifications Power Power supply (Control and input) 24 VDC, 10%, Class2, 2 A 24 VDC, 10%, 8 A Power supply (Output) 24 VDC, +10/-5%, Class2, 2 A 24 VDC, +10/-5%, 8 A Enclosure IP67 (With
Circuit (Class 2) of maximum 30 Vrms (42.4 V peak) or less, with UL1310 Class 2 power supply unit or UL1585 Class 2 transformer. The product is a UL approved product only if it has a mark on the body. Use the specified voltage. Otherwise failure or malfunction can result. Insufficient supply voltage may not drive a load due to a voltage drop inside the product.
for centralized lead wire ISA-20 Stations Model 2 ISA-21-2 3 ISA-21-3 4 ISA-21-4 5 ISA-21-5 6 ISA-21-6 Regulator AR20-02-1-B -12No.PS-OMW0009-C 2 About this product 2 port solenoid valve VX210X276 Bracket (when control unit fitted) (Nominal size:3 x 8, 2 screws) ISA-17 Spacer with bracket Y200T-A Modular adapter E210-U01 Spacer ISA-18 With O-ring : When a 2 port solenoid valve is connected
Do not use the lock as a safety lock or a control that requires a locking force. Warning The lock used for the product with a lock is designed to prevent dropping of work piece. 2. For vertical mounting, use the product with a lock. If the product is not equipped with a lock, the product will move and drop the work piece when the power is removed. 3.
Recommended Parameter Values [LEF] LEFS25T6 LEFS32T7 LEFS40T8 Lead symbol H A B H A B H A B Series Lead 20 12 6 24 16 8 30 20 10 Parameter *1,*2 Para. Initial value Recommended value No.
(g) Bag/Box Quantity L2 D1 D2 M 1/4 1/4 3/8 3/8 3/8 1/2 1/2 5/8 1/4 SAE 1/2 SAE 1/4 SAE 3/8 SAE 1/2 SAE 3/8 SAE 1/2 SAE 1/2 SAE KV2H07-Q07 KV2H07-Q13 KV2H11-Q07 KV2H11-Q11 KV2H11-Q13 KV2H13-Q11 KV2H13-Q13 KV2H15-Q13 A A B A A B A B 12.4 12.7 12.0 16.2 16.2 14.5 17.3 15.1 17.9 17.8 29.0 21.5 21.2 31.9 22.4 35.0 5.5 5.1 17.0 5.3 5.0 17.4 5.1 19.9 16.0 23.0 22.0 19.0 23.0 26.0 23.0 29.0 12.0