Pressure Sensor Caution Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Warning Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Danger Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury. Warning 1.
Bore size (mm) Auto switch mounting surface 12 16, 20, 25 32, 40 Port side Port side Port side C A C A C A B B B Auto switch model Auto switch mounting surface Auto switch mounting surface Auto switch mounting surface Port side A, B and C sides A, B and C sides Port A, B and C sides qBQ-2 wBQ2-012 2 kinds of auto switch mounting brackets are available as a set.
Low frequency operation In order to prevent malfunction, conduct a switching operation of a valve every 30 days. Also, in order to use it under the optimum state, conduct a regular inspection once a half year. 17-6-10
Do not use a stopper cylinder for intermediate stopping of loads directly connected to a cylinder, etc. The operating ranges shown in the catalog should only be used for stopping pallets on a conveyor. If loads connected directly to a cylinder, etc., are stopped with a stopper cylinder, the cylinder's thrust will become a lateral load. Please consult with SMC in this case. Danger 1.
Do not use a stopper cylinder for intermediate stopping of loads directly connected to a cylinder, etc. The operating ranges shown in the catalog should only be used for stopping pallets on a conveyor. If loads connected directly to a cylinder, etc., are stopped with a stopper cylinder, the cylinder's thrust will become a lateral load. Please consult with SMC in this case. Danger 1.
Using a regulator on the secondary side When mounting a regulator on the secondary side (A port side), use a residual pressure relief regulator (AR2550 to 4050) or a check type regulator (AR2560 to 6060). With a standard regulator (AR1000 to 6000), the secondary side pressure may not be released when this valve is exhausted. 5.
P/As seal material has undergone a high vacuum degassing process. Orifice conductance In the case of a A (cm2) hole in an ultra-thin plate, the conductance C results from V the average velocity of the gas, R the gas constant, M the molecular weight and T the absolute temperature.
Nut Replacement Parts: Seal Kit (A rod seal @7, a piston seal @8 and a tube gasket @9 are included in the seal kits. Order the seal kits with ordering numbers.) Kit no.
Caution Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Warning Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Danger Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury. Warning 1.
Using a regulator in the outlet side When mounting a regulator in the outlet side (A port side), use a residual pressure relief regulator (AR25K to 40K) or a check type regulator. With a standard regulator (AR10 to 60), the outlet side pressure may not be released when this valve is exhausted. 5.
(A,MR~~N '(lmjQ' . 180 600 1100 1190 [Ereo flaw) Effettive ~IOnal 11.6 17 2.9 5.2 18.4 5.4 9.3 'ttrea mm 2 . N01e} The iMicaled 110w rate values are al a pressure 01 O.5MPa and a temperature 01 20 Q C. 1 Speed Controller 5 .
Take safety measures (e.g. mounting protective covers) when there is a danger of fingers being caught in a gripper or workpieces causing damage, etc. 3. There is a danger of workpieces dropping if there is a decrease in gripping force due to a drop in circuit pressure caused by a power failure or trouble with the air source.
It can cause a cylinder malfunction. eBecause the slider is supported by a precision bearing system, take care not to apply a strong impacts or excessive moments to the table when loading a workpiece. 4.7-3 Mechanical Joint Rodless Cylinder with Brake Hy-Rodless Cylinder SeriesML1 25, 32, 40 How to Order Hy-rodless cylinder (with brake) ML1C G 25 300 E73A Cylinder bore size Number of auto
Q 27 30 32 32 VCA21 VCA31 41 50 60 68 18 24 30 35 64 76 86 91 28 34 40 40 11.5 14 15 17.5 15 17 20 20 20.5 25 30 34 12.8 19 23 23 M4 M5 M5 M5 1/4 1/4, 3/8 3/8, 1/2 3/4 VCA41 17-2-13 8 Series VCA How to Order Manifold (VCA20) How to Order Manifold Assembly VV2C A 2 02 02 Enter the mounting valve and option part numbers under the manifold base part number.
Contact SMC if a stopper cylinder is to be used for stopping a load that is connected directly to a cylinder, as this will cause the cylinder's thrust to act as a horizontal load.
A ridge shape has been created as a Uni thread for common applications for Rc, G, NPT and NPTF. AS-FM Note) Universal type is not available.
For example, the bore size to move a workpiece with a weight of 37 kg requires a bore size of 43 or more.
Do not use in an environment where a heat source is at a close distance. 4. Do not use in an environment where static electricity is a problem. It may cause malfunction or failure of the system. Please consult with SMC for use in such an environment. 5. Do not use in an environment where spatters are generated. There is danger of fires caused by spattering.
Body size Symbol Symbol diameter 22 mm 26 mm 32 mm 5 6 16A 20A 25A 16 mm 22 mm 5 6 LVP6 Symbol Pilot port thread (fitting) type A Symbol Nil 1 2 N Thread (fitting) type 6 mm One-touch fitting Rc1/8 M5 x 0.8 NPT1/8 PA B N.C. A PB Option B Applicable valve type N.C. N.O. Double acting N.O.
Table 10-1 specifications EX245-FPS1 EX245-FPS2 EX245-FPS3 (W x L x H) mm 85 x 148.5 x 136 1,100 g 1,200 g 8 128 () 64 (US1) 350 mA 300 mA (US1/US2) XD1/XD2 16 A (US1/US2) 10 A (US1/US2) 24 VDC +20%/-15% <20.4 VDC US1 >21.6 VDC < 17 VDC 6 A 24 VDC +20%/-15% <21.6 VDC : >22.8 VDC US2 / <17 VDC 4 A () 1.2 V US1 US2 4 8 US1 UT1/UT2 24 VDC +20%/-15% 2 A( UT1) 1 A (