Compact Vacuum Ejector Series ZA Do not use for other purposes. Solenoid valve combination symbol Combination no.
Note 2) Do not form connection to pins indicated with . Note 3) Signal of negative-logic circuit ON (N.C.)
Do not leave out the component parts when the piping port location is changed. Even if one of the component parts is not replaced, malfunction may occur, resulting in dangerous operation. 2. To prevent air leakage, re-wind the pipe tape and fit into the changed location when the piping port location is changed.
Do not drop nor apply excessive force. It may cause a malfunction or damage. 3. Tighten IS1000-01 applying the spanner on the PT fitting part. CD-P11 Brown Choke coil Surge absorber Blue Warning Operating Environment CD-P12 (+) Brown 1. Avoid using a switch in a magnetic environment. It may cause a malfunction. 2. Do not use in such an environment, where water or oil is splashed.
When this is done, take care that the coverings of the lead wires do not enter the core wire crimping area. (Crimping tool: model no. DXT170-75-1) 1. Do not use with thinner, carbon tetrachloride, chloroform, acetate, aniline, cyclohexane, trichloroethylene, sulfuric acid, lactic acid and watermiscible cutting fluid (alkaline). 2. Operate it away from direct sunlight.
Do not allow repeated bending or stretching forces to be applied to lead wires. Wiring arrangements in which repeated bending stress or stretching force is applied to the lead wires can cause broken wires. 1. Do not drop or bump. Do not drop, bump or apply excessive impact (1,000m/s) when handling.
Caution Do not apply too much torque when turning the lock style manual override. (0.1Nm or less) 1.10-195 VQ 0/1000 Plug Lead Unit Base Mounted Precautions Be sure to read before handling. Refer to p.0-33 to 0-36 for Safety Instructions and common precautions.
Do not drop or bump. Do not drop, bump or apply excessive impact (1,000 m/s2) when handling. Even if the switch body is not damaged, the switch may suffer internal damage that will lead to malfunction. 2. Hold the product from the body side when handling. The tensile strength of the power cord is 49 N, and pulling it with a greater force can cause failure. 3.
(Do not tighten with pliers.) I @silrc SERIES NCDJ2 Connection examples to relay and solenoid valve Basic wiring 3 wire system (When power source for switch and load is common) Rd lead wi: Connect io the power sourc e (powet source lerminal) lo operare main circuit of switch.
Note 2) Do not release the OUT side piping port of the product directly to the atmosphere without connecting piping. If the product is used with the piping port released to atmosphere, accuracy may vary.
Do not use a screwdriver with a large grip or with a tip that does not fit into the trimmer groove because this could strip the groove.
voltage suppressor VZ 4(A)/2(B) port size Type of actuation VF Manual override Electrical entry Rated voltage Thread type Body option VFR Option 1 0 5 01 L Body ported VZ5 2 VP4 VZS Type of actuation Option VFS 2 position single solenoid F: With foot bracket (2 position single type only) Body option VS4 1 0: Individual exhaust for the pilot valve VQ7 2 position double solenoid EVS Note) Do
MGG (Max.)W1 B DX Z + Stroke MGC DDH10 hole 90 B MGF 4-DT B DS A DH DF CY1 DO DO DC DE DU DU DL DA 4-DR MY1 Rotation angle (mm) Bore (mm) 40 50 63 80 100 Bore (mm) 40 50 63 A B A + B + 90 Part No.
Do not install by directly grasping the cylinder tube, as this could cause a tube to deform and malfunction. 2. Do not install it by directly grasping the piston rod with a pair of electricians pliers. Scratches on the piston rod would cause a bearing or rod seal to get damaged, malfunction, and leak air. 10 12.4 4 15 12.8 20 13.2 16
Do not use this aftercooler in an area that has viscous dust (electrostatic paint powder, oily particles, etc.). If it must be used under such conditions due to unavoidable circumstances, please contact SMC beforehand.
Option Port size (P, A, B port) Thread type Nil F G Rc Nil Z None Nil 01 Without sub-plate 1 8 1 4 With light/surge voltage suppressor 02 N NPT Piping (P, A, B, EA, EB port) T NPTF EA, EB port: Rc 1/8 Nil B Side ported Bottom ported Option SJ 1 00 01 F Plug-in VFR2 5 SY 1 E 10 1 Non plug-in VFR2 02 SV CE-compliant SYJ Q CE-compliant Nil Pilot valve manual override SZ Electrical entry: D/DO
Note 1) Do not use the product in an atmosphere and place where there is direct contact with chemicals. It may cause damage to the body. (Alcohol, acetone, etc. also cause damage, so be sure for the product not to be close to them.) Note 2) Do not use it in a line that is kept pressurized because it could cause the body to break.
(Fig. 1) Also, do not use the cylinder with fixed at external slider to avoid excessive moment applied to bearing of the cylinder.
Conditions for mechanical operation Do not move the mechanical operation beyond the operating limit position, as this could damage the mechanical valve itself and lead to equipment malfunction. Actuator stroke Operate the mechanism within the stroke range that has been obtained through the formula given below. (Do not move beyond the operating limit position.)
Lube Cast iron Chromated (In the case of aluminum alloy casted) Aluminum alloy casted (Iron tube: Cast iron) Non-lube Piston Chromated (In the case of aluminum alloy casted) Aluminum alloy casted (Iron tube: Cast iron) Air-hydro Caution Mass/Aluminum Tube: Lube (Non-lube, Air-hydro) Do not open the cushion valve excessively.