MY1 Remove the covers as shown in Figure 2 and make further adjustment by loosening the hexagon nut. 3. Various dimensions are indicated in Table 1. Never make an adjustment that exceeds the dimensions in the table, as it may cause an accident and/or damage.
[An asterisk () indicates those that are the same as standard.]
The position of spanner should be a root as close as possible to R thread. Hex. across flats may be deformed, if using an improper wrench for hex. across flats.
Model number: HRR012/018/24/030-AN/WN-10/20 The transition connector from Rc to NPT is enclosed as an accessory. For NPT piping, be sure to use this connector. Model number: HRR012/018/024/030-AF/WF-10/20 The transition connector from Rc to G is enclosed as an accessory. For G piping, be sure to use this connector.
Pad Caution Guide for drop prevention Provide an auxiliary device (example: a guide for preventing the workpieces from dropping) as necessary. Mounting Position As a rule, the unit must be installed horizontally.
IC chips With adapter Single unit Nozzle 0.8, 1.1 P. 9 AN Thin Flat Pad For adsorption of soft work pieces such as thin sheets or vinyl.
Therefore, the flow rate is calculated as the formula: Q = 0.05/1 x 20 = 1 [kg/h]. Specific Product Precautions 58 JSXD Series Flow Rate Characteristics * Use this graph as a guide. In the case of obtaining an accurate flow rate, refer to pages 54 to 58.
Holding of pressure (including vacuum) Since valves are subject to air leakage, they cannot be used for applications such as holding pressure (including vacuum) in a pressure vessel. 5. Cannot be used as an emergency shutoff valve, etc. The valves presented in this catalog are not designed for safety applications such as an emergency shutoff valve.
Depending on the external switch output type, wire the switch to the communication connector for contact input / output (which is included as an accessory) as shown below. Mount the ferrite core (3 turns), which is included as an accessory. This is an example of wiringRefer to the Communications Operation Manual for more details.
Protective class class # (Mark: ) 120 JSY3000 Series Specify the valve manifold and mounted valve part numbers as well as the ejector manifold and mounted ejector part numbers for ordering. Refer to page 120 for an order example.
W/o auto switch B L L1 With auto switch Bore (mm) 5st 10 A 20 20 20 20 5st 10 5st 10 5st 10 32 48 58 12 33.5 58 68 17 38.5 40 64.5 12 33.5 64.5 74.5 17 38.5 45.5 50 67.5 77.5 18 43.5 87.5 97.5 28 53.5 Rod end male thread Double clevis (mm) A Without auto switch B CL A B CL With auto switch Bore (mm) Double clevis/CQ2D, CDQ2D 5st 10 20 20 20 20 20 20 5st 10 5st 10 5st
Enable Generates an error. 1 Unit Disable Does not generate an error. -10..10 V -5..5 V -20..20 mA 0..10 V 2 Analogue input range Sets the analogue input device range. Selects the analogue input range. -10..10 V Channel 0..5 V 1..5 V 0..20 mA 4..20 mA Offset binary Offset binary.
Lead 20: LEYG32A 30 30 20 20 0 0 0 200 600 1000 1400 1200 Speed [mm/s] 0 200 600 1000 1400 Speed [mm/s] 866 A Model Selection LEYG Series Motorless Type * These graphs show an example of when the standard motor is mounted.
[Tips]
Please match the controller upstream devices, such as a PLC, with the pulse input signal type. When using the upstream devices with a differential output and the controller as an open collector input, the Card Motor may travel twice as fast as the output pulse of the upstream devices. iii.
Model number: HRS030-N-20 The transition connector from Rc to NPT is enclosed as an accessory. For NPT piping, be sure to use this connector. Model number: HRS030-F-20 The transition connector from Rc to G is enclosed as an accessory. For G piping, be sure to use this connector.
(It is an example of model "HRS040-A-20".)
[Tips]
20 16 20 24 24 20 25 26.5 26.5 22.5 23.5 32 27.5 27.5 Note 1) Figures in the table above are used as a reference when mounting the auto switches for stroke end detection.
Since Series CHQB does not have an air release plug, release air from other components (e.g. from piping, etc.) as well. 6. When mounting the cylinder body with mounting bolts, use the tightening torques in the table at right as a guide.