Made to Order Through-hole/Both ends tapped (Standard): MK2TB MK2T-XC89 Lube-retainer Coil scraper 2 x P Cylinder port M A C G thread length H L N C A KA I KK 2 x J 4 x J K D 0.07 0.15 4 x F counterbore C S T AB AA MM KB Q R 2 x E through 2 x FF counterbore (mm) MM KB KK FF AB AA I N M L K J H G F E D C A KA Bore size 32 40 50 63 0.07 0.15 14 50 9 depth 11 9 depth 7 M10 x 1.5 8 4 46 45 34 6 M6 x 1.0 21
Grease may enter into the outlet port of the valve. 2. When using vacuum pressure for the VM100, supply vacuum pressure to P port.
In case of Long Stroke For long stroke operation, the cylinder tube may be deflected depending on weight and load; in that case, support the center on the cylinder with a side support so that the supporting interval will be lower than the value shown in the diagram.
Rear plate N C D T A 2 x P (Rc, NPT, G) Q B E W S U M K L R I AP AB J AA A V Y + Stroke X Z + Stroke 8 x AF AC AD AE WH (Max.)
If the exposed tip of the optical cable is dirty, optical transmission may be interrupted and may cause malfunctions. If the tip becomes dirty, wipe with a bonded textileor similar. Do not use a solvent such as alcohol. Click Tab (b) Removal While holding the tab on the SSCNET cable connector, remove the connector.
This may cause malfunction of the vacuum pump. 6. When the capacity of the vacuum pump is relatively small or when the inside diameter of the piping is small, a change in the set pressure (the pressure difference between the non-flow and flow conditions) may be large. In this case, change the vacuum pump or the inside diameter of the piping.
If the end face of optical code tip is dirty, optical transmission may be interrupted and may cause malfunctions. If the tip becomes dirty, wipe with a bonded textile, etc. Do not use a solvent such as alcohol. Click Tab (b) Removal Whilest holding the tab on the SSCNET cable connector, remove the connector.
If it is pulled off at an angle, the pilot valve may be damaged or the protective O-ring may be scratched. Installation Put the cover back on straight without touching the pilot valve, and push it all the way until the cover's hook locks, without twisting the protective O-ring. (When pushed in, the hook opens and locks automatically.)
The warranty period of the product is 1 year in service or 1.5 years after the product is delivered, whichever is first.2) Also, the product may have specified durability, running distance or replacement parts. Please consult your nearest sales branch. 2.
Omron AB2 Accessories I Part # I Description D-sub cable with connectors on both ends Input Base Unit Input Expander Unit VVZR3000-21 A-6-X2 I EX300-IB1-AB I EX300-IE1-AB ) Series NVFR3000:Base Mounted 1Ype Construction/Parts List NVFR3100 NVFR3200 2 position double A B 2 position single AB ~;\ll1h?
M12 x 25L AH AT AB E TR AU AO * Supplied with 2 foot brackets and 4 mounting screws.
Also, since there is an internal voltage drop of 4V, it may not be possible to confirm the OFF and ON states with a tester, etc.
If the signal is delayed, the piston rod (and load) may lurch at a speed greater than the control speed of the speed controller. Caution X Load center of gravity and cylinder shaft center are not matched. 1. Adjust the cylinders air balance.
If air is supplied and operation started without confirming the above condition, the cushion valve may be ejected from the cover.
The switch may be damaged if screws other than specified ones are used.
With non-polar type solenoid valves, at times of sudden interruption of the loading power supply, such as emergency shutdown, surge voltage intrusion may be generated from loading equipment with a large capacity (power consumption), and the solenoid valve in a de-energized state may switch over (see Figure 1).
SWEDEN SMC Pneumatics Sweden AB SWITZERLAND SMC Pneumatik AG.
Although the body of the switch may not be damaged, the inside of the switch could be damaged and cause a malfunction. 2. Do not carry a cylinder by the auto switch lead wires. Never carry a cylinder by its lead wires. This may not only cause broken lead wires, but it may cause internal elements of the switch to be damaged by the stress. 3.