Auto Switch Guide (Do not tighten with pliers.)
Do not drop or bump. Do not drop, bump, or apply excessive impacts (300 m/s2 or more for reed switches and 1000 m/s2 or more for solid state switches) while handling. Although the body of the switch may not be damaged, the inside of the switch could be damaged and cause a malfunction. 2. Do not carry a cylinder by the auto switch lead wires. Never carry a cylinder by its lead wires.
. 14 (7) Test operation . 14 3.
Do not use compressed air containing chemicals, synthetic oils containing organic solvents, salt or corrosive gases, as this can cause damage or malfunction. 5. Do not use until you can verify that equipment can operate properly.
RR1 RR1 E1 L1 MM A A1 U1 NDH10 NX +0.058 0 +0.058 0 +0.058 0 0.2 0.4 0.2 0.4 0.3 0.5 0.4 0.2 0.4 0.2 0.5 0.3 +0.058 0 +0.058 0 +0.058 0 16 20 22 I-G02 I-G03 I-G04 16 34 41 42 8.5 10.5 14 25 30 30 M8 x 1.25 10.3 12.8 12 11.5 14 14 20 25, 32 40 8 10 10 8 10 18 Y-G02 20 8.5 25 30 30 M8 x 1.25 10.3 12.8 12 16 20 36 21 IY-G02 IY-G03 IY-G04 34 41 42 11.5 14 14 8 8 20 M10 x 1.25 Y-G03 25, 32 40
Do not drop or bump. 5. Do not allow short circuit of loads.
(Do not tighten with pliers.)
Do not use in an environment with temperature cycles.
11 22 52 100.5 8 CLQ H GR H1 I N NA K L P PG PH PL PW RR S U Z ZZ MM NN Bore size (mm) 1/8 1/8 1/8 1/4 20 4 22 19.5 20 38 9 127 14 198 207 41 5 28 5 30 M8 x 1.25 15 24 M20 x 1.5 MLGP 25 7 27 24 24 41 9 137 14 212 221 45 6 33.5 5.5 30 M10 x 1.25 15 30 M26 x 1.5 32 7 27 24 24 41 9 139 14 214 223 45 6 37.5 5.5 30 M10 x 1.25 15 34.5 M26 x 1.5 RLQ 40 7 29 24 24 41 11 167 18 256 267 50 8 46.5
Made to Order Symbol 3 Model with 40 mm-pitch emitter cartridges X15 16 36 L 14 14 Install the emitter cartridges at a 40 mm-pitch. (Standard: 80 mm-pitch) Maintenance detection level selection switch KJH04-M5-X34 30 20 Position Detection Switch Flow Sensor Pressure Control Pressure Sensor Balance adjustment trimmer 14 19 20 16 Note) The maximum bar length is 1260 mm.
14 16.2 16.2 4 4 MK(2) Note) L, LL and S dimensions of RBL(C)1007/1006 are different from those of RB(C)1007/1006.
Do not apply torque at other points as the product may be damaged. Rotate body A manually for positioning after installation. 12. Do not use body A and/or elbow body for applications involving continuous rotation. Mounting Body A and the fitting section may be damaged. Warning 1.
(page 14-19-14) Operating Environment Caution 1. Do not use at temperatures (fluid or ambient temperatures) higher than the prescribed operating conditions. Resin is used in the membrane module, and it can be damaged by operation at high temperatures.
Do not mount this kit on other products. Carefully read the procedure manual included with this kit before performing the installation.
(67) (46) (26) IN Port size: 1/4 OUT Port size: 1/4 8 Width across flats 14 Width across flats 14 Width across flats 19 Width across flats 17 Purge air discharge tubing port for dehumidification Applicable tube O.D.: 6 (NPT thread: 1/4 inch) With fitting for purge air discharge (Option: P) (86) Purge air outlet for dehumidification (34) (67) (25) Width across flats 14 Width across flats
Safety Instructions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate or set with wet hands. This may lead to an electric shock. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result.
14 30 30 40 50 34 40 46 58 7.5 7.5 9 9 Rc1/8 Rc1/8 Rc1/4 Rc1/4 7 13 9 14 32 40 50 63 25, 50, 75, 100, 125, 150, 175, 200 250, 300, 350, 400 66 44 14 14 M8 X 1.25 M8 X 1.25 18 10 72 44 14 12 M10 X 1.5 M10 X 1.5 21.5 11 M10 77 49 16.5 16.5 M10 X 1.5 M10 X 1.5 28 13.5 WA R S T U VA VB WB Bore (mm) X XA XB XC XL YY YL Z 25st< 100st 300st< 100st< 200st 200 200 200 200 200st< 300st 33 34 36 38
Do not disassemble the cables. Use only specified cables. 3. Do not connect or disconnect the wires, cables and connectors when the power is turned on. Caution 1. Wiring securely. Do not apply any voltage to the terminals other than those specified in the Operation Manual. 2. Wire the connector securely. 3. Take appropriate measures against noise.
: 40, 50 40 50 Workpiece transfer direction Stroke 36 14 13.5 31 Width across flats K 10 7.5 7.5 2 x (Rc, NPT, G) 1/8 Z 20 24.5 8 T 0 0.1 E M J R38 25 14 28 B + Stroke 4 x N through 8 x O counterbore E M 100 + Stroke A + 2 stroke RSQ RSQ Mounting: Both ends tapped RSQA RSG RS2H O1 thread [mm] RSH Bore size B O1 R 32 48 M6 x 1 10 40 52.5 M6 x 1 10 50 54 M8 x 1.25 14 MIW MIS B + Stroke R R