Slide Unit/Double Rod Type Series CX2 Slide Bearing: ø10, ø15, ø25 Note 1) 5 to 50 mm/s 5 to 40 mm/s 5 to 100 mm/s Note 1) Consult with SMC when the air-hydro type is mounted on a plate. Note 2) Consult with SMC when units are used at a low speed (10 mm/s or faster) (when intermediate stops are not required) since -XB13 (Low speed specification) is available. Note 3) When using the air-hydro type, use the double side hydro unit.
PRODUCT SPECIFICATIONS S E R I E S I P 5 0 0 0 / I P 5 1 0 0 IP5000 (Linear) IP5100 (Rotary) SERIES 20 100 psi SUPPLY PRESSURE STROKE SENSITIVITY LINEARITY HYSTERESIS 0.4" 3.4" 60 100 degrees WITHIN 0.1% F.S. WITHIN 0.5% F.S. WITHIN 1% F.S. WITHIN 0.75% F.S. WITHIN 1% F.S. WITHIN 2% F.S. WITHIN 0.5% F.S.
Mount switches in locations without vibration (98m/s or less) or impact (490m/s or less). 3. Do not use in an area where surges are generated. When there are units (solenoid type lifters, high frequency induction furnaces, motors, etc.) which generate a large amount of surge in the area around switches, this may cause deterioration or damage to the switch.
.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com 0.03 s or less 0.03 s or less 0.05 s or less 0.05 s or less Response time Hysteresis 3% F .S. IR Repeatability 3% F .S. VEX Sensitivity 0.5% F .S.
Response time (With anti-chattering function) Output short circuit protection Display 2% F .S. 1 digit or less (at ambient temperature of 25 3C) Green LED (OUT1: Lights when ON), Red LED (OUT2: Lights when ON) Output voltage: 1 to 5 V 5% F.S. or less (in rated pressure range) Linearity: 1% F .S. or less Output impedance: Approx. 1 k No-voltage input (Reed or solid state), input 5 ms or more
PA 0 1 10 100 1000 Viscosity (mPas) = PAX = (103m2/s) = (mPas)/(kg/m3) PB 17-5-159 20 Series PAX Working Principle: Automatically Operated Type, Built-in Pulsation Attenuator Air supply port (AIR SUP) Air exhaust port (AIR EXH) Change lever Pulsation attenuator exhaust valve Pulsation attenuator intake valve Switching valve Control unit Drive unit Pilot valve A Pilot valve B Pump chamber
L, Z S L, Z S Note ) Thread PB 1 32A 40A 50A AC Flange DC Note) Surge voltage suppressor is attached in the middle of lead wire.
Z S L, Z S Note ) PAX 1 1 4 1 2 PB AC Ordering example (Example) Series VXR21, Rc 3/4, 24 VDC, Conduit terminal (Part no.)
Gap too small Green 2 a Place the gap gauge on the detection nozzle for precise adjustment. s Confirm applied air pressure.
Example: VEX1300-03 G36-4-01 (Constructive symbol) 5.1-1 VEX1 How to Order 1 03 D 3 1 0 B VEX Regulator valve B Bracket Option F Foot (Only VEX110) G Gauge When specifying more than one option, combine symbols in alphabetical order. 0 Air operated Operating style 1 External pilot solenoid None Indicator light and surge voltage suppressor S Surge voltage suppressor Z Indicator light and
SMC Corporation of America (Detroit) 2990 Technology Drive Rochester Hills, MI 48309 TEL: (248) 299-0202 FAX: (248) 293-3 w w w . s m c u s a . c o m SMC CORPORATION OF AMERICA U.S. HEADQUARTERS 3011 N. FRANKLIN ROAD INDIANAPOLIS INDIANA 46226
Calculation ZX ZR : Lifting force (N) : Stable vacuum pressure (kPa) : Pad area (cm2) : Factor of safety: Horizontal pad contact : 4 (dynamic) Vertical pad contact : 8 (dynamic) W P S t Pad ZM W = P x S x 0.1 x 1 t W ZH W ZU Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
@w, s Bore Siee Noaulo swjtch builtjn (hjglr magnelic Add L and Z at the end of part numberlor 3m and sfi, respectively. "ALrto switch detail: see pgs. 10-11.
rated pressure range, Ambient temperature 25 3C) Linearity 1% F .S. or less Repeatability 1% F .S. or less Power supply voltage effect 1% F .S. or less based on the analog output at 18 V ranging from 12 to 24 VDC Enclosure IP40 Temperature range 0 to 50C; Stored: 10 to 70C (No freezing or condensation) Resistance Withstand voltage 1000 VAC, 50/60Hz for 1 minute between external terminals
Make sure to connect a speed controller and adjust it to a speed of 500 mm/s or less to operate the cylinder.
Valve model Type of actuation Port size 1 4/2 (P A/B) Flow characteristics Note 2) Note 3) Effective area mm2 4/2 5/3 (A/B EA/EB) Weight (g) Pilot port size Cv C [dm3/ (s bar)] b Cv C [dm3/ (s bar)] b Grommet Single Double Closed center Exhaust center Pressure center Single Double Closed center Exhaust center Pressure center Single Double Closed center Exhaust center Pressure center 48
5.26 AIR PREPARATION HIGH FLOW SERIES LUBRICATOR SERIES (N)AL Port Sizes 1 12~2 Atomizes Lubricant into fine particles at a uniform rate Drip Rate easily monitored with Sight Dome Can be filled under pressure Bowl Guard Standard Damper precludes oil flooding S Y M B O L S H O W T O O R D E R L U B R I C AT O R S E R I E S NAL NAL800-N12 (1 14 NPT) NAL800-N14 (1 12 NPT) NAL900-N20 (2 NPT)
CDA2 B 50 200 X1184 B31J S With built-in special magnet Number of auto switches Cylinder stroke Description 2 pcs. 1 pc.
Note 1) 5 to 50 mm/s 5 to 40 mm/s 5 to 100 mm/s Note 1) Consult with SMC when the air-hydro type is mounted on a plate. Note 2) Consult with SMC when units are used at a low speed (10 mm/s or faster) (when intermediate stops are not required) since -XB13 (Low speed specification) is available. Note 3) When using the air-hydro type, use the double side hydro unit.