5 Port Solenoid Valve VQC5000 Bore size MB, CA1 series Pressure 0.5 MPa Load ratio 50% Stroke 500 mm CS1 series Pressure 0.5 MPa Load ratio 50% Stroke 1000 mm Average speed [mm/s] 50 63 80 100 125 140 160 180 200 250 1100 Vertically upward Horizontal 1000 900 800 700 600 500 400 300 200 100 0 Values at extension of a directly coupled cylinder when meter-out speed controllers are used with the needle full open
For Air 1.0 Downstream pressure of valve (P2) [MPa] Upstream pressure of valve P1z1.0 MPa 0.8 Subsonic 0.9 0.6 Critical pressure 0.8 0.7 Sonic 0.4 0.6 0.5 0.4 0.2 0.3 0.2 0.1 0 3/64 (1.2) 50 100 150 3/32 (2.4) 100 200 300 400 1/8 (3.2) 300 200 100 400 500 600 700 5/32 (4) 200 1, 000 800 400 600 7/32 (5.6) Series VXN2 250 500 7/32 (5.6) Series VXN3 500 1, 000 1, 500 2, 000 Flow rate Q [L/min
1000 25 200 400 600 800 1000 1200 1400 Flow rate Q [kg/h] ( ): Saturated steam holding heat (kcal/kg) ( ): Saturation temperature (C) For Water How to read the graph The pressure differential to generate a flow rate of 25 L/min water is as follows.
[L/min (ANR)] Discharge flow rate [L/min (ANR)] Suction flow rate [L/min (ANR)] Note 1) Air consumption [L/min (ANR)] Discharge flow rate [L/min (ANR)] 1,600 700 ---6 ---6 Discharge flow rate Discharge flow rate 1,400 Vacuum pressure [kPa] Vacuum pressure [kPa] 600 Vacuum pressure Vacuum pressure ---5 ---5 1,200 500 ---4 ---4 1,000 400 Suction flow rate Suction flow rate 800 ---3 ---3 300
ML2B + PLC (Overrun) (Run) Piston speed (mm/s) 100 0.5 300 1.0 500 2.0 800 3.0 1000 4.0 Stopping accuracy (mm) The graph below shows the relation between piston speed and overrun. (The length of overrun is changed dependent on piston speed, load, piping condition and control method. Be sure to adjust the stop signal position, etc. by trial operation with the actual machine.)
Franklin Road Indianapolis IN 46226 (317) 899-4845 www.smcusa.com Call 1-800-SMC-SMC1 (1-800-762-7621) to reach the branch nearest you 2004 SMC Corporation of America, All Rights Reserved. All reasonable efforts to ensure the accuracy of the information detailed in this catalog were made at the time of publishing.
.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com 45 95 150 170 250 350 450 770 960 Surface: Munsell N-5.5, Inner surface: Non coated Safety valve (1 pc.) R 1/2 R 3/4 R 11/4 R 2 R 1 Accessory (2) Rc 1/2 Valve for drainage (1 pc.) Pressure gauge (1 pc.)
RSH20, 32 Graphq Graphw 1.0 RSH32 RSH32 RSH32 Bore size 50, 63, 80/ m =0 Bore size 50, 63, 80/ m =0.1 RSH20 RSH20 RSH20 0.9 Operating pressure : P (MPa) 1300 1300 0.8 80 0.7 1200 1200 0.6 1100 1100 0.5 1000 1000 0.4 900 900 0.3 63 80 800 800 0.2 50 Weight : W (kg) Weight : W (kg) 700 700 0.1 600 600 100 200 300 400 500 0 63 500 500 Lateral load: W (N) 50 400 400 RSH50, 63, 80 300 300 1.0
For VM400/800 series valves, the piping method varies depending on the application (function); however, “NC,” “NO,” and “OUT” are stamped on each of the piping ports.
Check the JIS symbol in the location indicated in the “Dimensions” section of the VM400/800 series catalog to ensure proper piping.
(e.g., IR3020 sensitivity: 1.6 kPa←800 kPa x 0.2% [800 kPa = 0.8 MPa])
Series CM2 stainless steel cylinders are compact, lightweight and offer high performance. Improved piston seal and rod seal greatly improve the units life. Rubber bumpers are standard. The CM2 series offers a variety of mounting options and is auto switch capable. End lock cylinder, CBM2, Double acting, single rod, 8 mounting options available, Bore sizes: 20mm, 25mm, 32mm, 40mm, Auto switch
This is a legacy product. Please contact us for the latest version.sales@ocaire.com, CYLINDER, ACTUATOR, CBG1 END LOCK CYLINDER, LE, 32MM CBG1 DBL-ACT AUTO-SW, 2.16315 lb
This is a legacy product. Please contact us for the latest version.sales@ocaire.com, CYLINDER, ACTUATOR, CBG1 END LOCK CYLINDER, NE, 50MM CBG1 DBL-ACT AUTO-SW, 5.12201 lb
Series CM2 stainless steel cylinders are compact, lightweight and offer high performance. Improved piston seal and rod seal greatly improve the units life. Rubber bumpers are standard. The CM2 series offers a variety of mounting options and is auto switch capable. End lock cylinder, CBM2, Double acting, single rod, 8 mounting options available, Bore sizes: 20mm, 25mm, 32mm, 40mm, Auto switch
Series CG1 precision air cylinder has 8 bore sizes and can meet any application need. The tube is impact extruded aluminum to produce an extraordinarily smooth finish, allow low break-away pressure and smooth stroke action. Eight mounting options are available. Auto switch capable. End lock cylinder, CBG1, Double acting, single rod, 7 mounting styles available, Bore sizes *: 20, 25, 32,
This is a legacy product. Please contact us for the latest version.sales@ocaire.com, CYLINDER, ACTUATOR, CBG1 END LOCK CYLINDER, ME, 40MM CBG1 DBL-ACT AUTO-SW, 7.51577 lb
Air cylinder series CA2 has been introduced with specifications and dimensions equivalent to the existing CA1 series. Several improvements have been made to the CA2 series including lateral load improvement, increase in cushioning capacity and adoption of a new cushion seal. There has been enhanced efficiency in handling for cushion valve adjustment, and weight has been reduced by 5 to 15%
This is a legacy product. Please contact us for the latest version.sales@ocaire.com, MB CYLINDER, ACTUATOR, MB TIE-ROD CYLINDER, ME, 40MM MB DBL-ACT AUTO-SW, 6.17294 lb
This is a legacy product. Please contact us for the latest version.sales@ocaire.com, MB CYLINDER, ACTUATOR, MB TIE-ROD CYLINDER, ME, 40MM MB DBL-ACT AUTO-SW, 4.75827 lb
Air cylinder series CA2 has been introduced with specifications and dimensions equivalent to the existing CA1 series. Several improvements have been made to the CA2 series including lateral load improvement, increase in cushioning capacity and adoption of a new cushion seal. There has been enhanced efficiency in handling for cushion valve adjustment, and weight has been reduced by 5 to 15%