PF3W5.eng They are all important notes for safety and must be followed in addition to International standards (ISO/IEC) and other safety regulations. 4 Analogue output (flow rate) Rc(NPT)3/4 28 to 30 Nm Pin number of the connector at the body side Rc(NPT)1 36 to 38 Nm Maintenance Rc(NPT)11/4 40 to 42 Nm Element Description Rc(NPT)11/2 48 to 50 Nm How to reset the product after a power cut or when the
[F30] Storing of accumulated flow OFF [not held] Rc(NPT)1 36 to 38 Nm System error Turn the power off and turn it on again. If the failure cannot be solved, contact SMC for repair. [F80] Setting of power saving mode No setting [display is turned on] Rc(NPT)11/4 40 to 42 Nm Switch ON Switch OFF Do not touch the terminals and connectors while the power is on.
Nominal thread size Appropriate tightening torque Rc(NPT)3/8 22 to 24 Nm Rc(NPT)1/2 28 to 30 Nm Rc(NPT)3/4 28 to 30 Nm Rc(NPT)1 36 to 38 Nm If the tightening torque is exceeded, the product can be damaged. If the tightening torque is insufficient, the piping may become loose. The product body is made of resin.
Description PAX112 Diaphragm kit KT-PAX1-31 Check valve kit KT-PAX1-36 Switching valve parts kit KT-PAX1-37#1 Pilot valve kit KT-PA5-38 Pulsation attenuator control valve kit KT-PAX1-39 Piping and Operation Caution Mount the pump so that the reset button faces upward. Air to be supplied to the air supply port
type AXTS040*-3B-X2 External pilot valve Ratio of operating frequency and ON time AXTS040*-3(B)-X2 ON 10 OFF adjustment OFF[] Frequency [Hz] needle [rotation] 7 5 3 1 1 3 5 7 8 0.1 Hz 0.1 Hz 0.1 Hz 0.1 Hz [Hz] 1 6 2% 2% 1% 1% 2.0 Hz 2.3 Hz 2.4 Hz 2.0 Hz ON adjustme nt [Rotation] 4 Number of rotation of ON adjustment needle 3 OFF 29% 17% 15% 14% ON 2 [] 3.7 Hz 4.8 Hz 4.9 Hz 4.8 Hz 5 51% 36%
Port size Table 3-7 Piping port size Name Port size Recommended Recommended piping tightening torque specifications Circulating fluid outlet/ return port (CH1) *1 Rc1 36 to 38 Nm 1.0 MPa or more Circulating fluid outlet/ return port (CH1) *2 Rc1/2 28 to 30 Nm 1.0 MPa or more Circulating fluid outlet/ return port (CH2) Rc1/2 28 to 30 Nm 1.0 MPa or more Drain port Rc1/4 8 to 12 Nm Facility
PV SV 36. Select contact output 3 selected alarm from the table below with [] key or [] key, and confirm by pressing SEL. Table 2.4-19 List of set values Set values Explanation Initial value (Default setting) Setting/checking are not available unless the function setting of contact output 1 is selected alarm status signal. Sets selection alarm.
PV SV 36. Select contact output 3 selected alarm from the table below with [] key or [] key, and confirm by pressing SEL. Table 2.4-19 List of set values Set values Explanation Initial value (Default setting) Setting/checking are not available unless the function setting of contact output 1 is selected alarm status signal. to Sets selection alarm. Set range is AL.01 to AL.48.
Signal A DC output B DC output C DC output D DC output E DC output F DC output G FG DC connector (HED007-C2* 9.4 Specifications of Connectors 9-11 A_HEC-OM-K001-1.7 Chapter 9 Appendix 3) Signal connector HED003-C2*, HED005-C2*, HED007-C2* DDK: JMR1610FG-36 Connect the signal cable connector of Heat Exchanger. Pin No.
part) 6 (SUS304) Bellows (material: SUS316L) 5 Valve (material: SUS304) () 2 Valve seal (maintenance part) 4 (A6063) C C C C D D D D Body (material: A6063) K C C C C E E E E E E E E KF flange F F F Fn n n n (KF) () Heater (option) Auto switch H H H H J J J J G G G G B B B B A A A A A A A A Model A B C D E Fn G H J K XLC-25 50 120 48 1 12 40 26 39 27.5 8 XLC-40 65 171 66 2 11 55 41 63 36
Fix the width across flats (36) at the bottom of the bowl with a wrench and tighten it to the bowl. (Tightening torque: 20Nm) 5) Restart the operation 1. After the replacement of the element, check the parts are assembled correctly before restarting operation. In case of fluid leakage, stop the operation immediately.
JOG+ JOGPiston rod operation Moves to the retracted end direction OFF ON Retracted end Stops moving ON ON Stop Target position operation (4-20 mA) OFF OFF Retracted end Set point 36 7-2. Calibration The piston rod movement range (set point) can be set when using the Target position operation (refer to 7-3).
(Page 12) 0x0024 (36) 0 R Device Status N For more details, refer to "Device details status parameter." (Page 12) 0x0025 (37) 1..11 R Detailed Device Status N *1: R means Read and W means Write. *2Y is included in data storage, N is not included in data storage. *3: 8 octets fixed character string. *4: "x" represents a major revision number.
,,, 3-2 18 3-3 1 2 3 4 5 6 7 8 MXQ6(B),8(B,C),12(B,C) 9 Assy MXQ6A,8A,12A, MXQ16(A,B),20(A,B),25(A) 10 (MXQ6(B)) (MXQ8(A,B,C),12(A,B,C)) (MXQ8(A,B,C),12(A,B,C)) 11 (MXQ16(A,B),20(A,B),25(A)) (MXQ16(A,B),20(A,B),25(A)) 12 13 A 14 15 16 17 18 19 (MXQ6A,8A,12A, MXQ16(A,B),20(A,B),25(A)) 20 21 22 O 19 / 23 24 25 26 27 28 / 29 30 31 32 33 34 35 36
. (*2)Refer to P.27 7-3-6 Sequencer 36 9. Data Setting 9-1 Data Presetting 9-1-1 Data Classification & Content P1Cylinder Stroke Input stroke. P2Tolerance Input positioning tolerance range. Retries will assure the positioning within the tolerance range. P3Retries Input no. of retries. Maximum retries will be 9.
HOLDER 1 26 PISTON ROD 1 5 BRAKE METAL 1 27 PISTON B 1 6 PISTON A 1 28 CUSHION RING 1 7 ROLLER HOLDER 1 29 CUSHION RING B 1 8 ROLLER PLATE 2 30 CUSHION VALVE 2 9 NEEDLE ROLLER 2 31 CUSHION SEAL HOLDER 1 10 PISTON SPRING 1 32 TIE ROD 4 11 ROLLER SPRING 1 33 TIE ROD NUT 8 12 BUSHING 1 34 FLAT WASHER (8) In case of 80,100 13 HEXAGON SOCKET CAP BOLT 4 35 BUMPER A 1 14 HEXAGON SOCKET CAP BOLT 2 36
Size 90 180 With solenoid With auto switches1 Foot bracket Flange valves2 bracket 30 0.3 0.4 0.1 0.1 50 1.5 1.7 0.2 0.2 0.3 0.5 63 2.5 3.0 0.2 0.4 0.5 0.9 80 4.3 5.0 0.2 0.6 0.9 1.5 100 8.5 9.5 0.2 0.9 1.2 2.0 1 With 2 auto switches 2 The weight of the solenoid valve is not included. 17 - Table (4) Rotary actuator inner volume (cm3) Rotation angle Size 90 100 180 190 30 7.4 14 50 32 36
0.1 () (N) 0.5MPa 14 45 74 131 228 396 () 10,16,20,25 40mm 32,40 80mm 4 - 3. 3-1 3-2 3-3 1 ISO VG32 5 - 3-4 Nm mm Nm mm MHL2-10D M4X0.7 1.4 5 MHL2-10D M4X0.7 2.1 8 MHL2-16D M5X0.8 2.8 7 MHL2-16D M5X0.8 4.3 10 MHL2-20D M6X1 4.8 7 MHL2-20D M6X1 7.3 12 MHL2-25D M8X1.25 12 7 MHL2-25D M8X1.25 17.7 16 MHL2-32D M8X1.25 12 11 MHL2-32D M8X1.25 18 16 MHL2-40D M0X1.5 24 12 MHL2-40D M10X1.5 36
"Trigger LV(Trigger level) and Push speed(Pushing speed) do not need to be set because they are invalid when "Push force(Pushing force) is set to 1 or more. 36 - (2-3) Details of Position setting (When connecting to LECP or LECA) Refer to 5.1(1) to confirm TB Ver.
Occupied area Input 20 byte / Output 36 byte Connectable nodes Max. 65,535 nodes Vendor ID 0114h (276) Network topology Refer to the EtherCAT topology -13No. JXC-OMY0008-A 3.2 Parts Description Details of the parts of the controller.