Multi-Axis Step Motor Controller system Natural air cooling Operating temperature range 0C to 40C (No freezing) Operating humidity range 90% RH or less (No condensation) Storage temperature range 10C to 60C (No freezing) Storage humidity range 90% RH or less (No condensation) Insulation resistance Between all external terminals and the case: 50 MW (500 VDC) Weight 1050 g (Screw mounting), 1100 g (DIN rail mounting) *1 Do
" 0.006 8.3 Note 2) Rotating torque under pressure 0.5 MPa Note 3) Do not use the fittings with a leak tester or for vacuum retention because they are not guaranteed for zero leakage.
When installing and removing an element, do not scratch or damage it by touching the corners of the case, etc. When washing the element, do not wipe it using a stiff brush or rag. Refer to page 529 for Microswitch for differential pressure indication switch. r Removing the element Rotate the air breather (cap) one-third of a turn counterclockwise and remove it.
Do not service or attempt to remove product and machinery/ equipment until safety is confirmed. 1. The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or runaway of the driven objects have been confirmed. 2.
Do not bring objects that are sensitive to magnetism near the cylinder. The magnet is built into the cylinder. Do not bring magnetic disks, cards or tapes near the cylinder. Data may be lost. 5. If the cylinder is operated vertically with heavy loads, measures must be taken to prevent rapid extension of the piston rod when starting to operate in the downward direction.
Free mounting Speed controllers do not protrude from the top of the body. Top mounting Bottom mounting Side mounting Wiring and piping direction can be selected depending on mounting conditions.
(Do not use any tools.) The initial exhaust rate is adjusted by turning the adjustment nut counterclockwise. x Opening of the initial exhaust valve (valve S) When the pilot pressure is applied to the pilot port S, the valve S is removed from the valve S seal assembly, and the valve opens the adjusted amount.
Do not use it for mounting. Otherwise, the adjustment at shipment may deviate. 792
Do not drop, hit or apply excessive shock to the product. Even if the body is not damaged, the internal components may be damaged, leading to a malfunction. Wiring/Piping Warning 1. Power supply required to the product is 24 VDC and 1 A.
Do not make any upward angles in drain line.
Do not allow the weight of piping to be applied directly to the air dryer. HA AT ID Avoid installation on moving objects like trucks, ships, and so forth. Drain Tube AMG Caution AFF A polyurethane tube of 10mm outer diameter is provided as the drain tube for IDFS6E to 11E and IDUS3E to 6E. Use this tube to discharge drainage. Do not use the drain tube in an upward direction.
Free mounting Speed controllers do not protrude from the top of the body. Top mounting Bottom mounting Side mounting Wiring and piping direction can be selected depending on mounting conditions.
Therefore, do not touch its exterior surface because it could be very hot, depending on the energizing conditions.
Do not scratch or gouge the piston rod of the actuating cylinder, as this could damage the rod seal and lead to air leaks. The same applies to the guide shaft. 3. Make sure not to apply shocks or excessive moment to the slide block of the ball bushing type. 4.
This is a legacy product. Please contact us for the latest version.sales@ocaire.com
Series: 2 (VQ20), Stations: 12 Stations, Option: None, Thread: 00T (NPTF3/8)
Series: 2 (VQ20), Stations: 2 Stations, Option: None, Thread: 00F (G3/8)
Series: 2 (VQ20), Stations: 5 Stations, Option: None, Thread: 00F (G3/8)
Series: 2 (VQ20), Stations: 7 Stations, Option: None, Thread: 00N (NPT3/8)