SGC200-OMJ0004

8361: JIS B 9960-1: 1 ) JIS B 8433-1993: *2) , 1. 2. 3. 1. 2. 3. 4. 2 SGC200*-OMJ0004-A / / / / 1 1 1 1 1.5 1.5 1.5 1.5 *3) *3) *3) *3) 3) 3) 3) 3) 1 1 1 1 1 1 1 1 () 3 SGC200*-OMJ0004-A SGC/SGH Series SGC/SGH Series SGC/SGH Series SGC/SGH Series 2 2 2 2 / / / / ( ( ( ( ) ) ) ) () IP65 IP65 IP65 IP65 80100 ( ) 1) 1) 1) 1) 2) 2) 2) 2) 5 3) 3) 3) 3) , , , , 4) 4) 4) 4) , , , , 1)-10

Vinyl Chloride Air Operated Valve

1)No main pressure 2)Side failure of piston packing Check to proper pressure Yes Replace product 1)Internal lackage 1)Instrusion of particles 2)Flaws on valve seat Eliminate to proper pressure Replace product Failure of air tight 2)External leakage 1)Tightening failure 2)Breakage of Tighten additionally Replace product diaphragm 8 - Revision history 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101

FGX-OMZ0008

It cannot be cleaned. 10/12 FGX-OMZ0008 Replacement of element should be performed according to the procedure below. 1 Removal of the element.(See Fig.2 1) Stop operation. AIR VENT 2) Check following before maintenance.

Heat Resistant Solid State Auto Switch

No.D-S-OMS0002-B PRODUCT NAME Heat Resistant Solid State Auto Switch MODEL / Series / Product Number D-M9#J# Series Contents Safety Instructions 2 Model Indication and How to Order 8 Summary of Product parts 8 Definition and terminology 9 Mounting and Installation 10 Installation 10 Maintenance 12 Troubleshooting 13 Specification 17 Specifications 17 Dimensions 18 -1No.D-S-OMS0002-B Safety

5 Port Solenoid Valve

Please return the failed valve to SMC in the exact state when the failure occurred. 10 VP450-OMC0001-B A Renewal PX Revision history B Renewal Uy 1st printing: CV 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021 JAPAN Tel: + 81 3 5207 8249 Fax: +81 3 5298 5362 URL http://www.smcworld.com Note: Specifications are subject to change without prior notice and any obligation on the part of the manufacturer

Electro-pneumatic proportional valve

If short-circuit occurs, remove the cause immediately. 10 VEP-OMM0002-C VEP / VEF / VEA / VER Series Specific Product Precautions 5 Be sure to read before handling. VEA25 Caution for Mounting 1. Installation location Pay attention to the environmental conditions since this is an open type power amplifier.

Direct Operated 3 Port Solenoid Valve

Common exhaust Individual exhaust 10 VT315-OMH0002-D TROUBLE SHOOTING Should any trouble be found during operation, trace the source of the trouble in the following order and take corrective action.

BOOSTER RELAY

Bad characteristic Plugged restrictor Disassemble and clean Deformed diaphragm Replace diaphragm -9- No.IL01-OM06-C -10- No.IL01-OM06-C -11- No.IL01-OM06-C Safety instructions update Drawings update Spare parts list, Drawings update 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021 JAPAN Tel: + 81 3 5207 8249 Fax: +81 3 5298 5362 URL http://www.smcworld.com Note: Specifications are subject

Precision Regulator

This may cause misalignment of the pressure gauge pointer. -10- Operation Warning (1) Do not use a precision regulator outside the range of its specifications as this can cause failure.(Refer to the specifications.) (2) Screw a panel nut with the recommended proper torque 12.5Nm when mounting onto a panel.

Liquid Dispense Pump (solenoid type)

Check wiring. 10 If any abnormality is found, perform checks according to the following list. If the abnormality cannot be eliminated, contact your SMC representative. Discharge fluids from the pump. Eliminate the residual fluids, and thoroughly clean the product with pure water or air.

V100 Series

In the case of diodes, the residual voltage is approximately 1V. 10. Extended periods of continuous energization. If a valve will be continuously energized for an extended period of time, the temperature of the valve will increase due to the heat generated by the coil assembly. This will likely adversely affect the performance of the valve and any nearby peripheral equipment.

Lock unit

If alignment is not adequate, operation failure or breakage of the actuating cylinder or lock unit can result. 10 - Fig. 3.Example when operated with the rodless cylinder 2-3. Mounting The foot mounting cylinder has a hole in the foot to drive a pin into for accurate positioning and fixing.

2%F.S. 1 digitkPa Note 5) Minimum display: 10 to 50C (No condensation)IP65350 g

2%F.S. 1 digitkPa Note 5) Minimum display: 10 to 50C (No condensation)IP65350 g

2%F.S. 1 digitkPa Note 5) Minimum display: 10 to 50C (No condensation)IP65350 g

2%F.S. 1 digitkPa Note 5) Minimum display: 10 to 50C (No condensation)IP65350 g

2%F.S. 1 digitkPa Note 5) Minimum display: 10 to 50C (No condensation)IP65350 g

2%F.S. 1 digitkPa Note 5) Minimum display: 10 to 50C (No condensation)IP65350 g

The ZSE40A(F) is also CE, UL/CSA and RoHS compliant.High precision digital pressure switch w/2-color display , IP65 and RoHS compliant , Capable of copying up to 10 switches simultaneously , 3-step setting , Space saving design w/several piping and mounting variations, 2-Color Hi Precision Dig Pres Switch, VACUUM SWITCH, ZSE40, ZSE40A, 101 lb

The ZSE40A(F) is also CE, UL/CSA and RoHS compliant.High precision digital pressure switch w/2-color display , IP65 and RoHS compliant , Capable of copying up to 10 switches simultaneously , 3-step setting , Space saving design w/several piping and mounting variations, 2-Color Hi Precision Dig Pres Switch, VACUUM SWITCH, ZSE40, ZSE40A, 101 lb