EXxx-OMW0005 Note Please do not use it for purposes other than the original purpose. This connector may only be operated when under no load. Working with wet hands causes electric shock. Please never perform a repair.
(Do not use a tool.) For setting the initial pumped amount, turn it counterclockwise. 2. Opening the valve (valve S) for initial pumping When air pressure is applied to the pilot port 1(P) and the initial pumping solenoid valve is energized, the S valve will release from the S valve seal assembly and open to the adjusted angle. 3.
(The test was performed with the electric actuator in the initial state.) 8) Do not use the product in an environment where it is exposed to oils such as cutting oil, and water. Please install an appropriate protective countermeasure.
When the element comes to the end of its life immediately replace it with a new filter or replacement element (cartridge type). 4 Do not disconnect and replace the one-touch fitting. Environment Warning Warning 1. Do not use the product in the following environments, which could cause failure. Seals the element, cover and fitting body. A place exposed to water, steam or oil.
Do not use solvents such as benzene, thinner etc. to clean the product including the switch cover. Use a soft cloth to remove stains. Refer to the SMC website (URL http://www.smcworld.com) for more information about troubleshooting. This operation manual refers to all standard types and is partially applicable to special models.
Do not use solvents such as benzene, thinner etc. to clean the product including the switch cover. Use a soft cloth to remove stains. Refer to the SMC website (URL http://www.smcworld.com) for more information about troubleshooting. This operation manual refers to all standard types and is partially applicable to special models.
Do not use solvents such as benzene, thinner etc. to clean the product including the switch cover. Use a soft cloth to remove stains. Refer to the SMC website (URL http://www.smcworld.com) for more information about troubleshooting. This operation manual refers to all standard types and is partially applicable to special models.
for mounting attachment) 46 58 45 45 42 26H9 + 0.052 depth1.5 0 30 Positioning pin hole 60 18 5 86 30 107 Auto Switch Mounting Groove Dimensions M5 x 0.8 (Finger opening port) 14 24 M5 x 0.8 (Finger closing port) 42 8 3 4 3 MHY2-25D2 Opening/Closing direction through-hole type 4 x 5.5 through (Hole for mounting attachment) 12 -0.005 -0.025 6 12 22.5 (Limted area for mounting attachment) Do
Do not use the cylinder in the locked state to sustain a load that involves impact. Stopping Accuracy (Not including tolerance of control system.)
When air is supplied to all ports after the solenoid valve is pressure-center positioned, the pistons for rotary operation do not have any thrust, as the pressure in both sides is equal, and the pistons for rotary operation move to the center position due to the thrust of the pistons for center stop.
Do not place your fingers in the clearance between the non-rotating plate and the cylinder tube. Your fingers could get caught between the table and the cylinder tube when the piston rod retracts. If fingers are caught in a cylinder, there is a danger of injury due to the strong cylinder output, and therefore, caution must be exercised. 2.
Note) Do not apply rotational torque to the piston rod. q MK/MK2 RSQ/RSG Connect the shield wire to FG (frame ground).
Do not apply torque directly to the rod. Carbon steel Nickel plated Rod end nut !0 * NBR Rod seal !1 * NBR Piston seal !2 * NBR Tube gasket !3 Note 1) 12: Aluminum bearing alloy. Replacement Parts: Seal Kits Bore size (mm) Kit No. Contents CQSKB12-PS 12 CQSKB16-PS 16 Kits include items !1, !2 and !3 from the table above. CQSKB20-PS 20 CQSKB25-PS 25 *Seal kits consist of items !1, !
Caution Aluminum alloy cast (Steel tubing: Cast iron) Chromated (In case of aluminum alloy cast iron) Non-lube Piston Chromated (In case of aluminum alloy cast iron) Aluminum alloy cast (Steel tubing: Cast iron) Air-hydro Weight/Aluminum tube: Lube style (Non-lube style, Air-hydro style) (kg) Do not open the cushion valve excessively.
Adjust the opening/closing speed of the fingers with a speed controller so that they do not operate any faster than necessary. When fingers open and close faster than necessary, impact on the fingers and other parts increases, causing poor repeatability when gripping workpieces and danger of an adverse effect on the product's life. MRHQ25C P408080-3C 2.
Do NOT make upward piping. qFloat style auto drain (N.O.) 1)Use compressor with capacity more than 3.7kw{400L/min (ANR)}. 2)Set pressure more than 0.1MPa wFloat style auto drain (N.C.) 1)Compressor can be used even if energy is under 3.7kw. 2)Set pressure more than 0.15MPa wFloat style auto drain (N.C.) DO NOT pipe upwards. 1.4-13
Do not touch the lock ring. After removal, the lock ring will return to normal position automatically because of a return spring. eBy pushing tighter, lock portion goes over female side guide portion and snaps into window slot portion. Male side protruding portion snaps into female side groove portion. This performs the function of a detent.
The resulting impact cannot be absorbed easily, the stroke position cannot be maintained, and faulty operation may result. t Lubrication The bearing can be used in an oilless state, but when you are going to oil the bearings, do so by using a ball-cup so that no foreign matter will be mixed.
Do not over tighten the lock nut. 4.7-7 Series ML1 Basic Style Bottom side piping port size Mounting side should be processed according to the dimensions below.
Do not service machinery/equipment or attempt to remove component until safety is confirmed. 1) Inspection and maintenance of machinery/equipment should only be performed after confirmation of safe locked-out control positions. 4-17-4