CM2x-OM0230Q 3. <> () () 6080 D-M9A(V) M3M3 0.6 0.7Nm (M2.5) (M2.5)0.050.1Nm 56mm 1) (M2.5) 2) M3 BM5 12 - 13 - 3. 14 - 1) 2)1 (30) * *(NC=b )(D-M9E(V)) 15 - / 16 - 3.
For single power supply use COM C COM C is receiving data: Lights up COM C is having no data to receive: Goes off 24 VDC 24 VDC COM D COM D is receiving data: Lights up COM D is having no data to receive: Goes off : It is lit when input unit is connected and communicating normally. 24 VDC 19 18 Display/ Switch Setting (continued) Switch setting Make sure that switch setting is performed
Auto switch Auto Switch Specifications D-M9-5(With indicator light) Auto switch model D-M9P-5 Wiring 3-wire Output PNP type Applicable load IC circuit,Relay,PLC Power supply voltage 5 , 12 , 24 VDC (4.5 to 28 V) Current consumption 10 mA or less Load voltage 28 VDC or less Load current 40 mA or less Internal voltage drop 0.8 V or less at 10 mA (2 V or less at 40 mA) Current leakage 100 A
Tube size (mm) Coil (mm) Tube size (mm) Coil (mm) Tl No. of tubes Max. operating length (mm) No. of tubes Max. operating length (mm) L D O.D. I.D. O.D. I.D. L D Part No.
(NPN) 3-wire (PNP) 2-wire IC circuit 5 V, 12 V 12 V Diagnostic indication (2-color indication) Auto switches marked with are produced upon receipt of order.
Power supply (24VDC or 12 to 1sVDC) is required. Note 2) Select either analog output or switch output When switch output is selected, select either NPN output or PNP output.
NAL800 100 283 59 112 Flow rate quoted at: 0.5MPa supply 0.03MPa pressure drop NAL900 100 288 63 2 H O W T O O R D E R L U B R I C AT O R S E R I E S AL AL800-12 (1 14 PT) AL800-14 (1 12 PT) AL900-20 (2 PT) FOR FURTHER TECHNICAL DETAILS ON THIS PRODUCT CONSULT SMC CUSTOMER SERVICE
(mm) 4 6 8 10 12 M I.D. (mm) 2.5 4 5 6.5 8 H White (W) D Black (B) Red (R) MS Blue (BU) T Yellow (Y) Green (G) VMG Air/Nitrogen gas/Water (Pure water) (1) Fluid Max. operating pressure (at 20C) 0.7 MPa (2) Min. bending radius (mm) 10 20 25 30 40 Burst pressure Refer to the burst pressure characteristics curve.
) Note 12) Note 12) i ZA Note 11) Pressure unit Name plate, caution plate for bowl, and pressure gauge in imperial units (PSI, F) Digital pressure switch: With unit switching function Note 13) Note 13) Note 13) Note 10) For thread type: NPT.
Plug-inmManifold for VQ1*0* valve, D-sub connector (25 pin standard, 15 pin option), Top or side receptacle position, Maximum 24 stations available as standard, 16 port sizes available, Optional DIN rail mount, MFLD, PLUG-IN, VQ1000, VALVE, VV5Q* MANIFOLD VQ 4/5 PORT, U5, VV5Q* BUILT IN FITTING 2.50775 lb
We guarantee that the product complies with the outline dimensions provided. d.
Construction ASB Series 12 - ASB-D Series 13 - ASB-BD Series 14 - ASB-*H Series 15 - S Revision history A : Added the construction of ASB-BD series Corrected the component contents of ASB-D series B : Added the ASB-*H series 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021 JAPAN Tel: + 81 3 5207 8249 Fax: +81 3 5298 5362 URL https://www.smcworld.com Note: Specifications are subject to change
Push-turn locking slotted type [Type D] Push down on the manual override with a small flat head screwdriver until it stops. Turn it clockwise by 90 to lock it. Turn it counterclockwise to release it.
ALARM (24) Alarm output 2 NO.1 12 General-purpose input NO.2 COM (12, 25) Common The output terminal common. 3 < 1 > NO.3 13 NO.4 4 NO.5 14 5 NO.0 15 6 NO.1 16 < 2 > 7 NO.2 17 General-purpose output 8 NO.3 18 9 NO.4 19 10 NO.5 20 57 Series LC1 Series LC1 Timing for temporary stop during operation Timing for READY signal generation immediately after turning on power HOLD ON OFF ON OFF Power
Recommended Tightening Torque [Nm] Connection thread Pressure Control Equipment 1/2 3/8 1/4 1/8 Torque 28 to 30 22 to 24 12 to 14 7 to 9 2. Avoid excessive torsional moment or bending moment other than those caused by the equipments own weight as this can cause damage. Support external piping separately. 3.
Recommended Tightening Torque [Nm] Connection thread Pressure Control Equipment 1/2 3/8 1/4 1/8 Torque 28 to 30 22 to 24 12 to 14 7 to 9 2. Avoid excessive torsional moment or bending moment other than those caused by the equipments own weight as this can cause damage. Support external piping separately. 3.
Fieldbus interface connector layout BUS OUT/Port2: M12 4-pin socket, D-coded (SPEEDCON) No. Designation Description 1 TD+ Transmit Data + 2 RD+ Receive Data + 3 TDTransmit Data 4 RDReceive Data BUS IN/Port1: M12 4-pin socket, D-coded (SPEEDCON) No.
D: Contents revised in several places. [September 2016] E: Contents revised in several places.
Auto switch Auto Switch Specifications D-M9N-5(With indicator light) Auto switch model D-M9N-5 Electrical entry direction In-line Wiring 3-wire Output NPN type Applicable load IC circuit,Relay,PLC Power supply voltage 5 , 12 , 24 VDC (4.5 to 28 V) Current consumption 10 mA or less Load voltage 28 VDC or less Load current 40 mA or less Internal voltage drop 0.8 V or less at 10 mA (2 V or less
Correspondence between output data and valve manifold : Output numbers are assigned to stations from side D to U of manifold in order. (See manual of each valve manifold for the directions of side D and U) : Standard manifold is wired in double. Output numbers are assigned to side A and B alternatively. In case of single solenoid valve, output on side B is free.