XLGR Series Dimensions E C D E E L (Width across flats) M (Width across flats) M8 (KF Flange) (K Flange) Fn Fd C Detail of (a) (a) M Rc1/8 J H K B A G A Model A B C D E Fn Fd XLGR-80*-1* 90 250 117 45.5 38.5 114 110 XLGR-100*-1* 108 270.5 154 55 38.5 130 102 XLGR-160*-1* 138 339 200 65 38.5 180 153 Model G H J K L M XLGR-80*-1* 83 105 44 9 13 4 XLGR-100*-1* 102 92 58 9 13 4 XLGR-160*-1* 153 124 62 12.5
GR-R-010(10g) 1 2 3) , 4 7 1 100 4 3g 1cm 1 2 100mm 7. 4. g 20 25 32 40 (mm) 100st 2 3 3 34 50st 0.5 0.5 0.5 1 19 3-2-4. 1) 8 8 2(9) 9 3) , 6 1mm 8. 9. 20 3-3. 3-3-1.
Auto switch operating range (mm) Auto switch model D-M9/D-M9W 12 16 20 25 32 40 50 63 3.5 5 5 5 6 6 6 6.5 7 9 9 9 9.5 9.5 9.5 11 D-A9 Values whitch include hysteresis are for guideline purposes only. They are not a guarantee (assuming approximately 30% dispersion) and may change substantially depending on the ambient environment. 14-5.
8.5 8.5 9 HYC Operating range 9 8.5 9 9 HYG Operating range 8 7.5 9 8.5 8.5 9 : It is not for guarantee but measure including hysteresis.
As a result, it could pose a hazard to humans and damage the machinery and equipment. (9) Do not apply a load that exceeds the values given in the catalog.
Piping Figure 8 and Table 9 show locations and sizes of piping ports. Ports can be selected from two sides. Plug the ports that are not used. Table 9 Port size Size Port size Size Port size A1, B1 A2, B2 10 M5x0.8 10 20 20 A1 30 Rc1/8 30 50 50 M5x0.8 B2 B1 G1/8 70 70 NPT1/8 100 100 Fig. 8 NPTF1/8 200 200 Rotary table ports and plate have a fixed orifice.
MHS4 -50D MHS4 -63D mm 16 20 25 32 40 50 63 MPa 0.20.6 0.10.6 -1060 mm 0.01 c.p.m. 120 60 10 19 31 55 88 140 251 1 N 12 21 35 61 97 153 268 mm 4 4 6 8 8 12 16 g 66 110 154 300 390 590 1,095 1) 1625 L=20mm 3263 L=30mm 0.5MPa 4 MHSJ3 MHSJ316D MHSJ320D MHSJ325D MHSJ332D MHSJ340D MHSJ350D MHSJ363D MHSJ380D mm 16 20 25 32 40 50 63 80 MPa 0.20.6 0.10.6 -1060 mm 0.01 c.p.m. 120 60 30 9
JXC-OMT0034CN (GW)(CC-Link) / LEC-GMJ2 1. . 4 2. . 6 2.1 . 6 2.2 . 6 2.3 . 7 2.4 () . 8 (1) . 8 (2). 8 (3)(LEC) . 8 (4). 8 (5) . 8 (6) . 9 (7) . 9 3. . 10 3.1 . 10 3.2 . 12 3.3 . 13 (1)(LECGMJ2) . 13 (2)DIN (LECGMJ2D) . 13 3.4 . 14 (1) . 14 (2) . 14 4. . 15 4.1 (STATION NO.,B RATE) . 15 4.2 (CN2SW) . 16 4.3 (LEC) . 17 5. . 19 5.1 CN4 . 19 5.2 CN3 . 19 5.3 CN1CONT . 19 5.4 CN2PC
Skin the cable and crimp the crimped terminal (9) to the edges. 3) Remove the screw (3f) from the bracket (3e). (Loosen in the case of Y-shape type terminal.) As shown in the right figure, mount a crimped terminal (9), and then again tighten the screw (3f). Note) Tighten within the tightening torque of 0.5 Nm 15%. Note: a) It is possible to wire even in the state of bare wire.
Same as for union nut tightening. 9 3.
Every time the button is pressed, the value will change from A to Z and 0 to 9. When the button is pressed, the value changes in the opposite direction. : If the password does not match, "wrong password" is displayed on the input screen.
Application 9 4. Specifications 9 5. How to Operate 9 6. Troubleshooting 9 7. Construction 1011 -2- Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of Caution, Warning or Danger.
Pneumatic circuit The basic circuit for operating the product with air filter, regulator, solenoid valve and speed controller is shown in Figure 8 and 9. Regulator Regulator Speed controller Speed controller Pressure source Pressure source Filter Filter Cylinder Cylinder Solenoid valve Solenoid valve Figure-8. Single acting Figure-9.
Ambient environment use shielded 9 8 7 6 HECR012-W 4 Unused Unused cable connected When turning on/off the power observe the procedure. Otherwise 5 SG SG to this connector. D-sub 9 pin (socket type) Temp :-40 to 70 C (No dew condensation and icing) Humidity : 5 to 95%RH Environment : No corrosive gas, solvent such as thinner and flammable gas unexpected malfunction or danger may occur.
SUS+NBR 1 3 Piston Stainless steel 1 2 Head cover Brass 1 Electroless nickel plated 1 Body Aluminum alloy 1 Hard anodized No Description Material Qty Note 29 6 7 3 6 1 With auto switch 10 8 4 11 9 2 5 12 13 13 Magnet holder Brass 1 12 Magnet Magnetic material 1 11 Gasket NBR 1 10 Rod seal NBR 1 9 Piston seal NBR 1 8 Bumper Urethane 2 7 Rod end nut Steel 2 Nickel plated 6 Mounting nut Brass
to 16 stations SY3000-43-2ASY3000-43-3AType D, 9 to 16 stations Type u, 2 to 8 stations 7 Connector assembly SY3000-43-1NASY3000-43-2NAType D, 2 to 8 stations Type u, 9 to 16 stations SY3000-43-2NASY3000-43-3NAType D, 9 to 16 stations Type u, 2 to 8 stations 8 Dust cup VZ3000-63-2 9 Round head combination screw SY3000-23-4 M326 Matt nickel plated 10 Gasket SX3000-57-4 SX5000-57-6 11 DIN rail
Heavy load Standard load Medium load Light load 1 10 50 100 200 1 0.25 0.49 0.98 1.96 2 20 2 0.49 75 200 400 0.74 1.47 2.94 3 30 3 0.74 100 300 600 0.98 1.96 3.92 4 40 125 400 800 4 0.98 1.23 2.45 4.90 5 50 5 1.23 150 500 1000 1.47 2.94 5.88 6 75 200 600 1200 6 1.47 1.96 3.92 7.84 7 100 250 700 1400 7 1.72 2.45 4.90 9.80 8 300 300 800 1600 8 1.96 2.94 5.88 11.76 9 500 500 900 1800 9 2.21
TROUBLESHOOTING 9 7. CONSTRUCTION / PARTS LIST 10-11 8. SPECIFICATIONS OF BOWL ASSEMBLY 12-17 9. REPLACEMENT PROCEDURE 18-21 10. DISASSEMBLY DRAWING 22-25 11. DIMENSIONS 26 Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage.
TROUBLESHOOTING 9 6. CONSTRUCTION / PARTS LIST 1011 7. BOWL ASSEMBLY SPECIFICATIONS 1219 8. REPLACEMENT PROCEDURE 2023 9. DISASSEMBLY DRAWING 2428 10. DIMENSIONS 29 S FILTER REGULATOR Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage.
D-sub 9 pin (socket type) Fixed screw: M2.6 6-8 Unused Unused 9 Unused BUS 1-2 Unused 8 1 Install the product above 0.6m from the floor. 3-5 PT-RTD 5.2 Environment 6 Output Cutoff Alarm a contact (OPEN During Alarm) 15 9 Signal D-sub 15 pin (Socket type) 7 Output Cutoff Alarm Common External Do not use in an environment where the product is directly exposed to Fixed screw: M2.6 temperature