Table of Contents Connect a drain pipe because a large amount of drainage is created when the compressed air is cooled. The drain pipe must have a minimum pipe bore of 10 mm, and a maximum length of 5 m (when installing an optional auto drain).
After tightening by hand, tighten an additional 1/4 rotation for M3 and 1/6 rotation for M5 with a tool. However, when using a miniature fitting, tighten an additional 1/4 rotation with a tool after tightening by hand. Also, when there are 2 gaskets such as for a universal elbow and universal tee, tighten an additional 1/2 rotation.
3 position exhaust center valve with a double check spacer, an intermediate stopping position of a cylinder can be held for an extended period.
141.1 99.2 99.2 19 42.9 (Lead wire length) 19 42.9 Polarity indication 13.6 13.6 A B A B B A A COM B + A B A B A B A Manual override (Push and turn for locking type) 42 31.4 Manual override (Press and turn for the locking type) 42 31.4 84.9 B: Green A: Orange 2-4.2 84.9 B: Green A: Orange 2-4.2 2-One-touch fittings (Mounting holes for manifold) (A, B port) (A, B port) 2-One-touch fittings
Switch When tightening an auto switch mounting screw, use a watchmakers screwdriver with a grip diameter of 5 to 6 mm.
For the protective tube, use a tube with a bore of 7 or more, which excels in heat resistance and flexibility. Contact SMC if an inverter welder or a DC welder will be used.
V (mm/s) = Operating range of auto switch (mm) Response time of electrical device (ms) x 1000 -X Auto switch 20Example The operating range of a D-A73L reed switch on a CD85E40 cylinder is 8 mm. It is necessary to use a solenoid valve with an electrical response time of 30 ms.
Install an air filter. Install an air filter upstream near the valve. Select an air filter with a filtration size of 5 m or smaller. 3. Take measures to ensure air quality, such as by installing an aftercooler, air dryer, or water separator. Compressed air that contains a large amount of drainage can cause the malfunction of pneumatic equipment, such as valves.
www.stevenengineering.com I 5.23 AIR PREPARATION SERIES NAP100 PRESSURE CONTROL VALVE The (N)AP Series pressure relief regulator is an adjustable re l i e f v a l v e w i t h a c o n t ro l r a n g e o f 1 8 ~ 1 0 0 P S I .
Never use in an atmosphere of explosive gases. 6. Do not use in an environment where there is excessive impact shock. The construction of auto switches is not intended to prevent explosion. Never use in an atmosphere with an explosive gas since this may cause a serious explosion. 2. Do not use in an area where a magnetic field is generated.
Never use in an atmosphere of explosive gases. 6. Do not use in an environment where there is excessive impact shock. The construction of auto switches is not intended to prevent explosion. Never use in an atmosphere with an explosive gas since this may cause a serious explosion. 2. Do not use in an area where a magnetic field is generated.
To use a single knuckle joint or a double knuckle joint concurrently with a rod end nut, extend dimensions A/H. (To extend dimensions A/H, refer to the table below, and specify the product as Order Made -XAO.) Single/Double knuckle joint mounting A, H dimensions at using both single/ double knuckle joint and rod end nut Symbol Bore (mm) Applicable knuckle joint part No.
An auto switch should be secured against a stopper in the auto switch groove for detection of valve opening, or at a position where it lightly touches a stopper or the valve body (depending on the valve size) for detection of valve closing. Auto Switch Specifications Auto switch part no.
Do not use an air cylinder as an air-hydro cylinder. This will cause leakage of hydraulic fluid. 9. Adjust an auto switch's position so that it operates for movement to both the stroke end and backlash (2 mm) positions. When a 2-color indication switch is adjusted for green indication at the stroke end, it may change to red for the backlash return, but this is not abnormal.
Use a single knuckle joint or a double knuckle joint individually.
CC series air-hydro unit, it is possible to operate at a constant or low speeds or to effect an intermediate stop, just like a hydraulic unit, while using pneumatic equipment such as a valve.
D-C7m/C80 D-C73C/C80C D-H7m/H7mW D-H7BA/H7NF Band mounting BJ2-010 (A set of band and screw) BJ2-016 (A set of band and screw) BQ2-012(S) (A set of a and b) BQ2-012(S) (A set of a and b) Set screw (Accessory) D-M9m D-M9mV D-M9mW D-M9mWV D-M9mA Note 5) D-M9mAV Note 5) D-A9m D-A9mV Note 4) Rail mounting BQ2-012 BQ2-012S a Auto switch mounting screw b Auto switch mounting bracket Nut (Cylinder
Cooling Method: A (Air-cooled Refrigeration), Pipe Thread: N [NPT (w/Rc-NPT Conversion Fitting)], Power Supply: 46 [3-phase 380 to 415 VAC (50/60 Hz); 3-phase 460 to 480 VAC (60 Hz)]
Cooling Capacity: 400 (38 kW), Cooling Method: A (Air-cooled Refrigeration), Pipe Thread: N (NPT, with Rc-NPT Conversion Fitting), Power Supply: 46 (50/60Hz: 3-phase 380 to 415 VAC; 60Hz: 3-phase 460 to 480 VAC)
Cooling Capacity: 150, Thread Type: N [NPT (w/Rc-NPT Conversion Fitting)], Power Supply: 46 [3-phase 380 to 415 VAC (50/60 Hz); 3-phase 460 to 480 VAC (60 Hz)]