Table of Contents Do not use this product on board a vehicle or a vessel. This product must not be installed and used on board a conveyance such as a vehicle or a vessel, as it may become damaged due to vibration. If it must be used in such a manner due to unavoidable circumstances, please contact SMC beforehand. 1.
Accessories Nil B None (standard) With bracket Note) When symbol B is indicated, a bracket assembly with a part number shown in the table below is included as an accessory.
Be careful not to squeeze it in the wrong direction, as problems such as pin damage may occur. (14.5) L How to Order Enter the part number for a plug connector solenoid valve without connector together with the part number for a connector assembly with cover.
tubing O.D. d D3 D1 AS-F TMH L4 L3 M ASD AS D2 AS-FE L5 A KE AS-FG AS-FG H T AS-FP L1 L2 AS-FM AS-D Metric Size [mm] AS-T Model d T H D1 D2 D3 L1 L2 L3 L4 L5 Note 1) A Note 2) M Weight [g] Unlocked Locked Unlocked Locked AS13l1FG-M5-23A 3.2 ASP 7.2 11.6 19.7 AS13l1FG-U10/32-23A AS13l1FG-M5-04A 4 8.2 17.5 33.8 ASN M5 x 0.8 10/32UNF 8 20.1 AS13l1FG-U10/32-04A AS13l1FG-M5-06A 6 10.4 21.2 20.4
SUP/EXH block Note 1) SSQ1000-PR-3-C8-(S) Back pressure check valve Note 2) SSQ1000-BP SUP block plate SSQ1000-B-P EXH block plate SSQ1000-B-R Port plug Note 3) P R A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B Note 4) C3 (N1) With 3.2 (1/8") One-touch fitting C4 (N3) With 4 (5/32") One-touch fitting C6 (N7) With 6 (1/4") One-touch fitting
Example) XLA-25H0-2M9NJLA-XAN1A 18 XLm Series Dimensions XLA/F (With D-M9mJm) C E E C E Fn D Heat-resistant auto switch H B A Heater G A [mm] Series Valve size A B C D E Fn G H 25 50 121 48 27 12 40 26 44 40 65 171 66 39 11 55 41 67 50 70 185 79 46 11 75 52 72 XLA XLF XLC/G25, 40 (With D-M9mJm) XLC/G50 (With D-M9mJm) C E C E E C E E C E Fn B A Fn D D Heat-resistant auto switch H J K H B A
Non-standard strokes for a size 6 cylinder are available as a special order. Made to Order Specifications (For details, refer to page 8-31-1.)
Brass Brass Rolled steel Rolled steel Rolled steel Rolled steel Urethane Urethane NBR NBR Aluminum alloy Aluminum alloy 40 or larger: the same as damper A Except for 80 and 100 Nickel plated 32 or more: the same as A Nickel plated/Except for long stroke Electroless nickel plated Electroless nickel plated Nickel plated 32 or larger: the same as A 32 or larger: the same as A White hard anodized
Through the concurrent use of a CC series air-hydro unit, it is possible to operate at a constant or low speeds or to effect an intermediate stop, just like a hydraulic unit, while using pneumatic equipment such as a valve. A cushion mechanism is provided on the cover at both ends to absorb the impact that is created during high speed operations.
the piston rod material will be treated as a special order.
the piston rod material will be treated as a special order.
value no more than the values in the table as a guide.
value no more than the values in the table as a guide.
Especially in the case of small diameter pads. 6.When transporting in an upward direction, factors such as acceleration, wind pressure and impact force must be considered in addition to a workpiece weight. Use caution particularly when lifting items such as glass plates and circuit boards, because a large force will be applied by the wind pressure.
As shown in the below figure, mount a crimped terminal (9), and then again tighten the screw (3e). Note) Tighten within the tightening torque of 0.5 Nm 15%. Note: a It is possible to wire even in the state of bare wire.
Note 3) When tightening an auto switch mounting screw (M2.5), use a watchmakers screwdriver with a grip diameter of 5 to 6 mm. Also, set the tightening torque to be 0.05 to 0.15 Nm. As a guide, turn 90 from the position where it comes to feel tight. 1.
9 Baking Gases such as oxygen and nitrogen, which have a small adsorption activation energy (E) and a short adsorption residence time (), are evacuated quickly.
In order to further improve stopping accuracy, the time from the stop signal to the operation of the lock should be shortened as much as possible. To accomplish this, use a device such as a highly responsive electric control circuit or solenoid valve driven by direct current, and place the solenoid valve as close as possible to the cylinder. 8.
10 18 The body mounting reference plane should be used as a standard when mounting onto equipment.
value no more than the values in the table as a guide.