o ORemole drainage from the system because large quantity ol drainage causes pneumatic product mallunction as well as environmental contamination. For added con\,/enience, the use ol an auto d rain is recom mended. Owhen there is a large amount of carbon powder trom the comDressor. it causes valve malfunction.
ORemole drainage from the system because large quantity ol drainage causes pneumatic product mallunction as well as environmental contamination. For added con\,/enience, the use ol an auto d rain is recom mended. Owhen there is a large amount of carbon powder trom the comDressor. it causes valve malfunction.
Be sure to use the cushion mechanism of the cylinder or the buffer mechanism, such as the shock absorber so that any impact force is not applied to the floating joint when stopping a driven body. If there is no buffer mechanism, an excessive impact force is generated. As a result, the tensile compression force of the floating joint may exceed its maximum level.
When designing an application, be sure to allow sufficient space for maintenance and inspection. In cases of high piston speed, the use of an auto switch (DF5NT/F7NT/G5NT and M5T) with a built-in OFF delay timer ( 200 ms) makes it possible to extend the load operating time. 4. Wiring should be kept as short as possible.
Note 2) Voltage symbol 23 (230 VAC) and 46 (460 VAC) are the terminal block connection as standard. The option S cannot be chosen. Voltage symbol 11 (115 VAC) is the power cable with plug as standard.
Smooth operation and longer life from an oil containing slide bearing. Rotary seal A special rotary seal minimizes friction while providing an excellent seal.
OK OK Model determination Note 1) Stroke adjustment with either a bumper bolt or adjustment bolt is considered as an intermediate stop. Note 2) When an intermediate stop is performed with an external stopper, consider the dynamic load as shown below.
(-XC6) Caution Other specifications are the same as the standard model. Dimensions q Do not use the air cylinder as an air-hydro cylinder. This will cause an oil leak. w Install without twisting the bellows. If the cylinder is installed with its bellows twisted, it could damage the bellows.
Note) When placing an order for body ported solenoid valve as a single unit, mounting bolt for manifold and gasket are not attached. Order them separately, if necessary. (For details, refer to page 4-4-11.) 4-4-6 7 3 Port Pilot Operated Solenoid Valve Rubber Seal Series SYJ300 Construction (A) 2 (A) 2 N.C.
However, when mounting a blanking part to a valve, place an order for a separate gasket (SYJ700-5-3) when placing an order for the valve. When using the SYJ700-10-1A, a gasket for this blanking plate assembly can be used as a gasket for the valve as well.
As the standard electrical wiring specifications, double wiring (connected to SOL. A and SOL. B) is adopted for the internal wiring of each station for 8 stations or less, regardless of valve and option types. Mixed single and double wiring is available as an option. For details, refer to page 2-4-29.
Air Cylinders Applicable for use in an environment with water splashing such as food processing and car wash equipment, etc.
Air Cylinders Applicable for use in an environment with water splashing such as food processing and car wash equipment, etc.
How to Order Type 46 (5 Port/Base mounted) Applicable solenoid valve SYJ340SYJ343SS5YJ3 46 05 M5 Type 46 Type S46 ( ) Single solenoid coil is on same side as the A, B port. M5 x 0.8 R1 R2 port Applicable blanking plate assembly SYJ3000-21-2A Stations Valve mounting direction 02 2 stations Single solenoid coil is on opposite side as the A, B port.
Use the air dryer with an ambient temperature lower than 40C. Avoid installation on machines for transporting, such as trucks, ships, etc. Avoid locations which experience sudden pressure/flow rate changes.
52 46 55 63 69 S 33 36 40 46 50 52 Z 46 52 56 65 73 79 6 10 16 20 25 32 7 9 12 16 20 24 6 depth 4.8 6 depth 5 7.6 depth 6.5 9.3 depth 8 9.3 depth 9 11 depth 11.5 5 7 Free Mount Cylinder Double Acting, Single Rod Series CU Proper Auto Switch Mounting Position (Detection at stroke end) and Its Mounting Height D-A9 D-M9 D-F9W 22 (24.5) ( ): Denotes the values of D-A93.
The purpose of an air cushion is not to reduce the speed of a piston as it nears the stroke end.
The product can be used at an ambient temperature as low as 20C, but take measures to prevent the solidification or freezing of impurities, etc. 2. When using for water, etc. in a cold area, devise a means to prevent freezing, such as draining the water from pipelines after stopping supply and exhaust water for a pump or other device.
2 q q AS y !3 w y t AS-FE w i t KE o AS-FG AS-FG i !0 u AS-FP !0 o e AS-FM !4 u Meter-in type Meter-out type AS-D e Seal method: Face seal For G thread AS-T Meter-in type Meter-out type ASP !1 ASN r !2 AQ q w ASV y t AK i VCHC o ASR ASQ !0 u !5 e Meter-out type Meter-in type Component Parts No.
Use the slotted head set screw with urethane damper as auto switch mounting screw.