Precision Regulator Before using the precision regulator, be sure to install the pressure gauge at the gauge port of the precision regulator. At this time, the recommended tightening torque of the pressure gauge is 7 to 9 Nm. 822 IR1000/2000/3000 Series Specific Product Precautions 2 Be sure to read this before handling the products.
Slroke = 079 (20mrt) w h Boot Mr limelers i. Parenlneses CPA1 BN do Boot with Boot' BORE D E G'GB J K M MM N P H z.
Slroke = 079 (20mrt) w h Boot Mr limelers i. Parenlneses CPA1 BN do Boot with Boot' BORE D E G'GB J K M MM N P H z.
The screw on the topmost section is a zero point adjustment screw which is locked at the factory and requires no adjustment for operation. 1. Do not use a precision regulator outside the range of its specifications as this can cause failure. (Refer to specifications.) 2.
Add the symbol at the beginning of part numbers for electro-pneumatic regulators, etc. to be mounted on the base. Note 1) Electro-pneumatic regulators are counted starting from station 1 on the left side with the OUT ports in front. Note 2) The port size for mounted electro-pneumatic regulators is Rc(PT)1/4 only.
Installation at indoor site (for air cooled type) 1. For a facility having a large installation area (that can vent the air naturally): Make an air outlet on a wall at a high level and air inlet on a wall at a low level, to allow for adequate airflow. 2.
Flashes during anti-freezing function (At standby: Interval 2 seconds, At operation: Interval 0.3 seconds).
T type interface cannot be mounted at IN/OUT side of AW or upward handle of AR. When T type interface is used at IN side of lubricator, oil may have entered.
Flashes during anti-freezing function (At standby: Interval 2 seconds, At operation: Interval 0.3 seconds).
Flashes during anti-freezing function (At standby: Interval 2 seconds, At operation: Interval 0.3 seconds).
Flashes during anti-freezing function (At standby: Interval 2 seconds, At operation: Interval 0.3 seconds).
Flashes during anti-freezing function (At standby: Interval 2 seconds, At operation: Interval 0.3 seconds).
o 85% RH lor lmin between and 50Mti or more (at belween bad wires and body In X. Y, Z directions 3limes each 12.6FS or lesis at 25'C 01: Rl/8. [.r5 x 0 8, Tl: NPT1/8, M5 x 0 8.
o 85% RH lor lmin between and 50Mti or more (at belween bad wires and body In X. Y, Z directions 3limes each 12.6FS or lesis at 25'C 01: Rl/8. [.r5 x 0 8, Tl: NPT1/8, M5 x 0 8.
Mount an auto switch at the center of the operating range. In the case of 2-color display auto switch, mount it at the center of the green LED illuminating range. Adjust the mounting position of the auto switch so that the piston stops at the center of the operating range. (The mounting position shown in the catalog indicates the optimum position at stroke end.)
When one side is fixed When an actuator is operated at a high speed with one end fixed and the other free (basic, flange, or direct mount types), a bending moment may act on the actuator due to the vibration generated at the stroke end, which can damage the actuator.
Wall *1 For air-cooled type, leave a space of at least 600 mm between the heat exhausting surface and the wall. For water-cooled type, leave a space at least 600 mm between the facility water piping side and the wall. Leave at least 600 mm on the sides indicated with .
Place the housing including the bowl assembly on the body at the position with configuration match by checking the appearance of them and fix it by four hexagon socket head cap screw by hexagon wrench. Tightening torque at this time is shown on Check item. And the screw which is tightened next after first tightened screw shall be what is located at cross corner of first one.
At the same ozone concentration of 1.1ppm, approximately 25% of the ozone still remains in the circuit as measured at point downstream of the mist separator (AM) at an atmospheric dew point of 10C. When the atmospheric dew point is 17C, approximately 45% of the ozone still remains.
Place the housing including the bowl assembly on the body at the position with configuration match by checking the appearance of them and fix it by four hexagon socket head cap screw by hexagon wrench. Tightening torque at this time is shown on Check item. And the screw which is tightened next after first tightened screw shall be what is located at cross corner of first one.