Flow Control Equipment

ASV How to Order AK 01 06 S AS 1 1F G 2 2 ASS Body size 1 2 3 4 Options M5 S None Sealant 1 8, 1 4 8 3 Applicable tube O.D.

PF3A7xxH.eng

When the output is ON: Orange LED is ON. (4) Press and hold the S button for 2 seconds or longer to complete the OUT setting. (If the button is pressed for less than 2 seconds, the setting will be returned to P.)

PFMB.eng

Power is supplied S S S SET (S) button Press this button to change the mode and to set a value. L Press the S button for 2 seconds or longer. DOWN () button Selects the mode and decreases the ON/OFF set value. M Setting F0 Setting F1 Setting F99 N Indicates the unit currently selected. Unit display The output will not operate for 3 seconds after supplying power.

Stainless Steel Cylinder Series CJ5-S/Series CG5-S

16 S R 60 H7BAL With Auto Switch With auto switch (built-in magnet) Number of auto switches 2 pcs. 1 pc.

PF3A7xxH_eng

return to measurement mode by pressing the S button for 2 seconds or longer. 3: When the output mode is set to error output or output OFF, the simple setting mode cannot be used.

PSE100

Input set point value for OUT1 (2) OUT2 OUT1 CH.B CH.A OUT2 OUT1 CH.B CH.A OUT2 OUT1 CH.B CH.A "OUT1(2) mode"is enterd by pressing the button "S" "Out2(3) mode" is enterd by pressing the button "S" Press the button "S" 3 seconds or less: Selected channel 3 seconds or more: Not selected channel Gbutton: Increase set point value Hbutton: Decrease set point value R button: Reads the pressure

100

, 7-segment, 2-color LCD (Red/Green) Sampling cycle: 5 times/s Display accuracy 2% F.S. 1 digit (Ambient temperature of 25C) Indicator light Lights up when switch output is turned ON.

PF3W7x.eng

[F 3] [ FiL] Digital filter setting [ 1.0] 1.0 s 3 DC(-) Blue 0 V [ dEF] Standard (OUT1 set value displayed) : When a temperature sensor is not connected. 4 OUT1 Black Switch output 1 NOTE The direct current power supply used should be UL approved as follows. Circuit (Class 2) of maximum 30 Vrms (42.4 V peak) or less, with UL1310 Class 2 power supply unit or UL1585 Class 2 transformer.

ZSE40/ISE40

Immediately after supplying power, there is drift of about 0.5% F .S. When used with very low pressure, allow the unit to warm up for about 20 to 30 minutes. MPa 2. Do not use in locations where there is splashing or spraying of oils and solvents. 3. When using a commercially available switching regulator, be sure to ground the FG terminal. OUT2 OUT1 SET 4.

PSxx-OMM0002CN

2 Max.80 mA 1 V T15 V 1 k V420 mA 12 V 300 24 V 600 50 -V/-T () PNP 2 Max.80 mA 1 V -A NPN2 Max.28 V80 mA 1 V -B PNP2 Max.80 mA 1 V -18No.PS-OMM0002CN-F ONOFF () ON OFF ON5OFF 20 P 1 H_1 [Pa] ON OFF [s] -19No.PS-OMM0002CN-F <> (19) 1 [P_1][n_1] 1 1 2[P_2][n_2] 2 (P1L P1H ) P1L()P1H() (n1L n1H) (24 ) 1 -20No.PS-OMM0002CN-F 2 [F 0] [F] 2 2 [F][-] [F 0] 23 ISE80(H) MPa

ZISE10.eng

Pressure Setting In measurement mode, press the button for 2 seconds or longer to display [F 0]. Select to display the function setting to be changed, [F ]. Press the button for 2 seconds or longer in function selection mode to return to measurement mode. Measurement mode Press the button for 2 s or longer.

IZE11.eng

Product type 2. [P_1] and set value are displayed in turn. Displays in turn approx. 1 s Pin number Wire colour Mounting and Installation Switch output type 1 Brown (DC+) Troubleshooting approx. 1 s 2 N.C. CAUTION indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Caution: 3 Blue (DC-) Analogue output type Installation 3.

AC Servo Motor Driver (MECHATROLINK-III type)

Alarm] [Software Reset] [ALM-CLR] ON Reset button Execute button FL-1*2 System Alarm FL-2*2 Alarm CPF00 Digital Operator Transmission Error 1 CPF01 Digital Operator Transmission Error 2 A.

AC Servo Motor Driver (MECHATROLINK-II type)

Alarm FL-2*2 CPF00 Digital Operator Transmission Error 1 CPF01 Digital Operator Transmission Error 2 A.

Programless Controller (With Stroke Study) ® Specialized for Series LEM Series LECP2

B-1 A-1 B-2 A-2 B-3 A-3 Connector C terminal no. Signal Cable color S Standard cable Brown Red Orange Yellow Green Blue A A B B COM-A/COM COM-B/ 2 1 6 5 3 4 Cable color Connector D terminal no.

ZISE80.eng

(See the figure below) Measurement mode Press the button for 2 s or longer. In measurement mode, press the button for 2 seconds or longer to display [F 0]. Select to display the function to be changed, [F ]. Press the button for 2 seconds or longer in function selection mode to return to measurement mode.

ZISE40A.eng

Specification NOTE The direct current power supply to be used should be UL approved as follows : Circuit (of class 2) which is of maximum 30Vrms (42.4V peak) or less, with UL 1310 class 2 power supply unit or UL 1585 class 2 transformer. The Pressure switch is a approved product only if it has a mark on the body.

ZISE30A.eng

Function selection mode Measurement mode Press the button for 2 s or longer Tube After maintenance is complete, perform appropriate functional inspections and leak tests. Stop operation if the equipment does not function properly or there is a leakage of fluid. When leakage occurs from parts other than the piping, the product might be faulty.

PF3A8xxH.eng

S S S Flow direction (1) Press the SET button once when the item to be changed is displayed on the display. The set value on the sub display (right) will start flashing. The output will not operate for 3 seconds after supplying power. The identification code of the product is displayed.

Seal: R (Rubber), Size: 2 (Size 18mm), Configuration: FG (2-position), Number of Solenoids: D (Double), Voltage: 3 (24VDC), Light/Surge Voltage Suppressor: Z (Indicator Light, Surge Voltage Suppressor), Manual Override: Push Type, Internal/External Pilot: Internal Pilot, CE Compliant: Q (CE Compliant)