Stainless Steel Cylinder Series CJ5-S/Series CG5-S 16 S R 60 H7BAL With Auto Switch With auto switch (built-in magnet) Number of auto switches 2 pcs. 1 pc.
return to measurement mode by pressing the S button for 2 seconds or longer. 3: When the output mode is set to error output or output OFF, the simple setting mode cannot be used.
Input set point value for OUT1 (2) OUT2 OUT1 CH.B CH.A OUT2 OUT1 CH.B CH.A OUT2 OUT1 CH.B CH.A "OUT1(2) mode"is enterd by pressing the button "S" "Out2(3) mode" is enterd by pressing the button "S" Press the button "S" 3 seconds or less: Selected channel 3 seconds or more: Not selected channel Gbutton: Increase set point value Hbutton: Decrease set point value R button: Reads the pressure
, 7-segment, 2-color LCD (Red/Green) Sampling cycle: 5 times/s Display accuracy 2% F.S. 1 digit (Ambient temperature of 25C) Indicator light Lights up when switch output is turned ON.
[F 3] [ FiL] Digital filter setting [ 1.0] 1.0 s 3 DC(-) Blue 0 V [ dEF] Standard (OUT1 set value displayed) : When a temperature sensor is not connected. 4 OUT1 Black Switch output 1 NOTE The direct current power supply used should be UL approved as follows. Circuit (Class 2) of maximum 30 Vrms (42.4 V peak) or less, with UL1310 Class 2 power supply unit or UL1585 Class 2 transformer.
Immediately after supplying power, there is drift of about 0.5% F .S. When used with very low pressure, allow the unit to warm up for about 20 to 30 minutes. MPa 2. Do not use in locations where there is splashing or spraying of oils and solvents. 3. When using a commercially available switching regulator, be sure to ground the FG terminal. OUT2 OUT1 SET 4.
2 Max.80 mA 1 V T15 V 1 k V420 mA 12 V 300 24 V 600 50 -V/-T () PNP 2 Max.80 mA 1 V -A NPN2 Max.28 V80 mA 1 V -B PNP2 Max.80 mA 1 V -18No.PS-OMM0002CN-F ONOFF () ON OFF ON5OFF 20 P 1 H_1 [Pa] ON OFF [s] -19No.PS-OMM0002CN-F <> (19) 1 [P_1][n_1] 1 1 2[P_2][n_2] 2 (P1L P1H ) P1L()P1H() (n1L n1H) (24 ) 1 -20No.PS-OMM0002CN-F 2 [F 0] [F] 2 2 [F][-] [F 0] 23 ISE80(H) MPa
Pressure Setting In measurement mode, press the button for 2 seconds or longer to display [F 0]. Select to display the function setting to be changed, [F ]. Press the button for 2 seconds or longer in function selection mode to return to measurement mode. Measurement mode Press the button for 2 s or longer.
Product type 2. [P_1] and set value are displayed in turn. Displays in turn approx. 1 s Pin number Wire colour Mounting and Installation Switch output type 1 Brown (DC+) Troubleshooting approx. 1 s 2 N.C. CAUTION indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Caution: 3 Blue (DC-) Analogue output type Installation 3.
Alarm] [Software Reset] [ALM-CLR] ON Reset button Execute button FL-1*2 System Alarm FL-2*2 Alarm CPF00 Digital Operator Transmission Error 1 CPF01 Digital Operator Transmission Error 2 A.
Alarm FL-2*2 CPF00 Digital Operator Transmission Error 1 CPF01 Digital Operator Transmission Error 2 A.
B-1 A-1 B-2 A-2 B-3 A-3 Connector C terminal no. Signal Cable color S Standard cable Brown Red Orange Yellow Green Blue A A B B COM-A/COM COM-B/ 2 1 6 5 3 4 Cable color Connector D terminal no.
(See the figure below) Measurement mode Press the button for 2 s or longer. In measurement mode, press the button for 2 seconds or longer to display [F 0]. Select to display the function to be changed, [F ]. Press the button for 2 seconds or longer in function selection mode to return to measurement mode.
Specification NOTE The direct current power supply to be used should be UL approved as follows : Circuit (of class 2) which is of maximum 30Vrms (42.4V peak) or less, with UL 1310 class 2 power supply unit or UL 1585 class 2 transformer. The Pressure switch is a approved product only if it has a mark on the body.
Function selection mode Measurement mode Press the button for 2 s or longer Tube After maintenance is complete, perform appropriate functional inspections and leak tests. Stop operation if the equipment does not function properly or there is a leakage of fluid. When leakage occurs from parts other than the piping, the product might be faulty.
S S S Flow direction (1) Press the SET button once when the item to be changed is displayed on the display. The set value on the sub display (right) will start flashing. The output will not operate for 3 seconds after supplying power. The identification code of the product is displayed.
6) 7) 20 No.ZL3-OM00801-A 9. 9.1 ZL3 ZL3M ZL3H [mm] 1.9 1.5 [MPa] 0.35 0.50 *1 -91 -93 [MPa] 280 [L/min(ANR)] + *2 300 [L/min(ANR)] 150 135 [MPa] 0.20.6 [] -550() 2] *2 20 [m/s 2] *3 100 [m /s *1 *22 2/V *310500Hz XYZ 2 *4XYZ 3 ZL6 ZL6M ZL6H [mm] 1.9x2 1.5x2 0.35 0.50 [MPa] 0.37 0.52 *1 -91 -93 [MPa] 580 [L/min(ANR)] + *2 600 [L/min(ANR)] 300 270 [MPa] 0.20.6 [] -550() 2] *
X B(ZS-24-B) M45L B -16No.PS-OMM0006CN-E M8(3) (ZS-35-C/ZS-35-D) +(ZS-35-F/ZS-35-G) () ZS-35-C/D -17No.PS-OMM0006CN-E 79 Nm M5 (12mm) 1 2 1) 0.1 mm 2)0.1 mm 3)+0.15 mm -0.2 mm -18No.PS-OMM0006CN-E () TU0425 ( 4 2.5) -19No.PS-OMM0006CN-E (M8(3)22) Z/ISE40A--DC(+) -S/-R () NPN 2 Max.28 V80 mA 1 V R15 V 1 k S420 mA 12 V 300 24 V 600 50 OUT1 OUT2 DC(-) DC(+) -S/-R () NPN 2
Set the adapter with 2 set screws. Time [s] button (UP) button (SET) To obtain more detailed information about operating this product, please refer to the SMC website (URL http://www.smcworld.com) or contact SMC directly. button (UP)
In measurement mode, press the S button for 2 seconds or longer, to display [F 0]. The [F ] indicates the mode for changing each Function Setting. Press the button for 2 seconds or longer in function selection mode to return to measurement mode. Displays the output status of OUT1 and OUT2. When the accumulated pulse output mode is selected, the output display will turn off.