Seal Type: S (Metal), Configuration: FG (2-position), Number of Solenoids: S (Single), Voltage: 3EZ (24VDC), Pilot: Pilot Exhaust through Footprint, Subplate: A02T (Side 1/4)
Seal Type: S (Metal), Configuration: FG (2-position), Number of Solenoids: S (Single), Voltage: 3EZ (24VDC)
Seal Type: S (Metal), Configuration: FG (2-position), Number of Solenoids: S (Single), Voltage: 3EZ (24VDC), Pilot: Pilot Exhaust through Footprint, Subplate: A03T (Side 3/8)
Seal Type: S (Metal), Configuration: FG (2-position), Number of Solenoids: S (Single), Voltage: 1Z (100VAC/50Hz, 115VAC/60HZ)
Seal Type: S (Metal), Configuration: FG (2-position), Number of Solenoids: S (Single), Voltage: 4EZ (12VDC), Pilot: Pilot Exhaust through Footprint, Subplate: A03T (Side 3/8)
HEC-OM-S019 Alarm b contact (CLOSE During Alarm) 10 Temperature Alarm Common 10 10m 02 2m 04 4m 06 6m N AC100V L AC100V 6-8 PT-RTD 5 Unused 9 Unused RS-485 Communication connector Note: Always use shielded cable connected to this connector. 6-9 Unused 3-4 Unused 3-5 Unused 1-3 Unused 12-14 Unused 1 BUS + 2 BUS 5 SG 4 FG 15 FG Power supply connector (IEC60320,C14) E PE HEA100 1 2 Specifications Continued
Response time 1 s or less Display accuracy 1.5%F.S. max.
Ensure that the FG terminal is connected to ground when using a commercially available switch-mode power supply. When a switch-mode power supply is connected to the product, switching noise will be superimposed and the product specification can no longer be met.
Ensure that the FG terminal is connected to ground when using a commercially available switch-mode power supply. When a switch-mode power supply is connected to the product, switching noise will be superimposed and the product specification can no longer be met.
Confirm that the power supply error (Er4, 6, 7, 8) is displayed. voltage is in the range of 12 to 24 VDC10%. 2. Supply an operating voltage of 12 to 24 VDC10%. The display 1. Confirm that the pressure is not 6 1. Return the pressure to within Applied pressure over the upper limit (HHH) over the upper limit of the set pressure range. shows "HHH". the set pressure range. 2.
-27-67 6 7. 0 ISE75 / ISE75H 8.
6 6 6 6 6 6 6-1 1 1 1 (DC12V60mA) B A G N D A B COM RS COM COM 12V G N D A B COM OUT1 AC100V OUT2 COM COM OUT3 COM DC24V GND AC100V (C E U 1) (C E U 1-D ) CEU1 +12V + 12V 1 A 680 CO M +12V + 12V 1 B 680 COM +12V D C 1 2 V60 m A GND RS COM FG AC100V 6 6 6 6-3 3 3 3 1C E U 1 CE1-R** 25m 3 4 SFC-10 5CEU1 AC 6 AC100V ( TDK ZGB2203-01U) (DC12V)(:ERZV10D220 7CEU1 10cm 8DC24V
Incorrect internal data processing of the product (Er0, 4, 6, 7, 8 and 9) Check if there is a noise source nearby. System error (Er0, 4, 6, 7, 8, 9) is displayed. (2) Check if the power supply voltage is in the range 12 to 24 VDC 10%. (2) Supply power in the range 12 to 24 VDC 10%.
HHH is 6 displayed. (1) Reset applied pressure (1) Check that the pressure is not LLL is to a level within the set pressure range.
An over current Incorrect internal data processing of the product (Er0, 4, 6, 7, 8 or 9) (1) Check if there is noise interference error (Er1, 2) is displayed. (such as static electricity. (2) Check if the power supply voltage System error is in the range 24 VDC 10%. (Er0, 4, 6, 7, 8 or 9) is displayed. (2) Supply power in the range 24 VDC 10%.
HHH is 6 displayed. (1) Reset applied pressure (1) Check that the pressure is not to a level within the set pressure range.
HHH is 6 displayed. (1) Reset applied pressure (1) Check that the pressure is not to a level within the set pressure range.
HHH is 6 displayed. (1) Reset applied pressure (1) Check that the pressure is not to a level within the set pressure range.
An over current Incorrect internal data processing of the product (Er0, 4, 6, 7, 8 or 9) (1) Check if there is noise interference error (Er1, 2) is displayed. (such as static electricity. (2) Check if the power supply voltage System error is in the range 24 VDC 10%. (Er0, 4, 6, 7, 8 or 9) is displayed. (2) Supply power in the range 24 VDC 10%.