Air Slide Table Series MXP MXP6 MXP8, 10, 12, 16 L2 L2 Shock absorber model RB0805 RB0805 RB0806 Applicable size MXP10 MXP12 MXP16 L2 Table 2 L2 (mm) 10 (one side only) 10 (one side only) 9 8 9 8 8 8 8 8 Model MXP6-5C MXP6-10C MXP8-10C MXP8-20C MXP10-10C MXP10-20C MXP12-15C MXP12-25C MXP16-20C MXP16-30C Stroke Adjustment Urethane bumper Lock nut Lock nut MXP6 MXP8, 10, 12, 16 Shock Absorber Loosen the lock nut, adjust
Note 3) Temperature conditions: at 20C (5C), in other cases, 6C F.S.
Use the product within the range of specifications for fluid and ambient temperature Take measures to prevent freezing when used at 5C or less, since moisture in circuits can freeze, causing malfunction. 2. Install air filters Install air filters near valves on their upstream side. The filtration degree should be 5 micron or less.
Take measures to prevent freezing at temperature below 5C, since moisture in circuits may freeze and cause damage to seals and lead to malfunctions. 5. Instruction manual Install the products and operate them only after reading the instruction manual carefully and understanding its contents. Also keep the manual where it can be referred to as necessary. Cushion Caution 1.
Take measures to prevent freezing at temperature below 5C, since moisture in circuits may freeze and cause damage to seals and lead to malfunctions. 5. Instruction manual Install the products and operate them only after reading the instruction manual carefully and understanding its contents. Also keep the manual where it can be referred to as necessary. Cushion Caution 1.
If the fluid temperature is 5C or less, the moisture in the circuit could freeze, causing damage to the seals and equipment malfunction. Therefore, take appropriate measures to prevent freezing. For compressed air quality, refer to Best Pneumatics No. 5. Lubrication Caution 1. The non-lube type air gripper is lubricated at the factory, and can be used without any further lubrication.
Mandrel Here, : Deformation ration (%) d: Tube diameter (mm) L: Measured length (mm) D: Mandrel diameter (mm) (Twice against the minimum bending radius) Handling of One-touch Fittings Test temperature: 20 5C Relative humidity: 65 5%. Caution 3. Applicable for general industry water. Please consult with SMC if using other fluids.
Ambient and fluid temperature operation is as follows: Digital pressure switches: 0 to 50C Other pressure switches: 0 to 60C Take measures to prevent moisture from freezing in circuits when below 5C, since this may cause damage to the O-ring and lead to a malfunction. The installation of an air dryer is recommended for eliminating condensate and moisture.
Ambient and fluid temperature operation is as follows: Digital pressure switches: 0 to 50C Take measures to prevent moisture from freezing in circuits when below 5C, since this may cause damage to the O-ring and lead to a malfunction. The installation of an air dryer is recommended for eliminating condensate and moisture.
Ambient and fluid temperature operation is as follows: Digital pressure switches: 0 to 50C Other pressure switches: 0 to 60C Take measures to prevent freezing moisture in circuits when below 5C, since this may cause damage to the O-ring and lead to a malfunction. The installation of an air dryer is recommended for eliminating condensate and moisture.
Ambient and fluid temperature range is as follows: Digital pressure switches: 0 to 50C Other pressure switches: 0 to 60C Take measures to prevent freezing of moisture in circuits below 5C, since this may cause damage to the O-ring and lead to malfunction. The installation of an air dryer is recommended for eliminating condensate and moisture.
m 2 ) VX32 AC (Full wave rectification) 50/60 10 8.5 60 1 3 5 0.08 1.5 1.0 0.6 220 1.9 VX311 -00 DC 8.5 60 11 60 9.5 50 1 3 5 0.16 0.5 0.3 220 3.8 VX312 -00 50 55 22 60 47 18 AC 0.6 370 VX3225-00 2.2 0.19 4.6 VX33 1.0 530 VX3325-00 AC (Full wave rectification) 50/60 14 11.5 60 1 3 5 0.24 DC 11.5 60 0.3 0.2 5.8 220 1.0 VX313 -00 Note) They are values in an ambient temperatue of 20C 5C
Port R Operating Fluid and Ambient Temperature Operating fluid temperature (C) (3) Vacuum Ambient temperature (C) Temperature conditions Air (Standard) Oil (Standard) (V) Port P Port A Maximum Minimum 60 5 (1) 40 5 40 40 5 5 (2) Note 1) Dew point: 5C or less Note 2) 500 cSt or less Note 3) V in parentheses is option symbol. Option Material No.
Water vapors in the circuit to be measured may freeze if the temperature goes below 5C and could damage the O ring or cause the switch to malfunction. The installation of an air dryer is recommended to remove any kind of moisture.
Buffer stroke 25 50 75 100 40 50 63 80 100 125 Series ZPT ZPX Pad Material and Characteristics : Little or no influence : Can be used depending on conditions X: Not suitable Characteristics Operating temperature range (C) Oil resistance gasoline Oil resistance benzol Solvent resistance (Benzene, toluene) Durometer HS (5C) Base resistance Acid resistance Abrasion resistance Ozone resistance
Moisture in circuits can freeze at 5C or below, causing damage to Orings, and malfunction. Consider measures to prevent freezing. The installation of an air dryer is recommended to remove drainage and moisture from circuits. Furthermore, even though the ambient temperature range remains within specifications, do not operate in locations where there are abrupt temperature changes. 2.
7.24 (184) 7.47 (200) (26) 9.13 (232) 9.76 \244) 1039 ( 4 ) '11'o2 (280) 11.66 (2e6)12.2a (32) 12.91 (328) t3 0.63 o6) 1.26 (32) 1.89 (4s) (64) 3.15 (80) 3.78 (e6) 4.41 1112) 5.04 (128) (i44) 6.30 (160) 6.93 (176) /.5tt (ie2) 8.19 (208) La2 (224)9.45 (240) 1008 (2s6) 10.71 1272) 11.34 \28) 11.97 (304) L, 0.31 (8) 0.94 (24) 1.57 (40) 2.20 (56.) 2.43 (72) 3.46 (88) 4.0s 004) 4-72 (120) c.5c
Take measures to prevent freezing, since moisture in circuits may be frozen under 5C, and this can cause damage to seals and lead to malfunction. Precautions when using external stoppers When the kinetic energy generated by the load exceeds the limit value of the actuator, an external shock absorbing mechanism must be provided to absorb the energy.
Take measures against freezing when operating at 5C or less. Mounting and Adjustment Caution 1. Do not drop or bump. Do not drop, bump or apply excessive impacts (980 m/s2 or more for sensor unit and 98 m/s2 or more for amplifier unit) while handling.