Vacuum Pad: Large/Heavy Duty Type Series ZPT/ZPX 0 to 120 30 to 200 0 to 60 0 to 250 20 to 150 x x x x Silicon rubber Urethane rubber Fluoro rubber x x x x x x x x x x x EPR x x x The above table covers only general characteristics of subject rubber materials.
Low temperature operation 1) The valve can be used in an ambient temperature of not less than 5C.
Use the product within the range of specifications for fluid and ambient temperature Take measures to prevent freezing when used at 5C or less, since moisture in circuits can freeze, causing malfunction. 2. Install air filters Install air filters near valves on their upstream side. The filtration degree should be 5 micron or less.
Use the product within the range of specifications for fluid and ambient temperature Take measures to prevent freezing when used at 5C or less, since moisture in circuits can freeze, causing malfunction. 2. Install air filters Install air filters near valves on their upstream side. The filtration degree should be 5 micron or less.
Port R Operating Fluid and Ambient Temperature Operating fluid temperature (C) (3) Vacuum Ambient temperature (C) Temperature conditions Air (Standard) Oil (Standard) (V) Port P Port A Maximum Minimum 60 5 (1) 40 5 40 40 5 5 (2) Note 1) Dew point: 5C or less Note 2) 500 cSt or less Note 3) V in parentheses is option symbol. Option Material No.
VlA Selection Caution Environment Warning VM/VR VH q Use in low temperature environments The valve can be used at a temperature down to 5C. Take appropriate measures to avoid freezing of drainage, moisture, etc. q When the valve is installed in an atmosphere where there is a lot of dust, install a silencer into the port "3(R)".
(For details, refer to pages 20 and 21.) Accessories Mounting Basic Axial foot Rod flange Head flange Single clevis Double clevis Center trunnion Standard Rod end nut V V V V V V V Clevis pin V Single knuckle joint V V V V V V V Double knuckle joint (with pin) V V V V V V V Option With rod boot V V V V V V V 2 B
Low temperature operation 1) The valve can be used in an ambient temperature of not less than 5C.
Take measures to prevent moisture from freezing in circuits when below 5C, since this may cause damage to the O-ring and lead to a malfunction. The installation of an air dryer is recommended for eliminating condensate and moisture.
If the fluid temperature is 5C or less, the moisture in the circuit could freeze, causing damage to the seals and equipment malfunction. Therefore, take appropriate measures to prevent freezing. Operating Environment Warning (1) Do not use in an atmosphere containing corrosive gases, chemicals, sea water, water, steam, or where there is direct contact with any of these.
If the fluid temperature is 5C or less, the moisture in the circuit could freeze, causing damage to the seals or equipment malfunction. Therefore, take appropriate measures to prevent freezing. For compressed air quality, refer to the SMC Best Pneumatics No. 6 catalog. 5.
Note 3) Temperature conditions: at 20C (5C), in other cases, 6C F.S.
./0.05 MPa Ambient and uid temperature 5C to 60C Port size Rc1/4 (Gauge port Rc1/8) Weight Approx. 700 g (at 100 mm stroke) Construction/Principle of Operation When signal pressure enters input chamber q, the input diaphragm e is deected left. Clearance of the nozzle y is reduced causing higher back pressure at diaphragm A u.
Clean Exhaust Filter SFE Series RoHS How to Order SFE 11 Size/Port size Male thread type Plug-in type Symbol Port size Max. ow capacity L/min (ANR) 11 M5 x 0.8 3 42 R1/8 65 52 R1/8 130 53 R1/4 130 73 R1/4 200 Symbol Port size Max. ow capacity L/min (ANR) 3A 4 30 4B 6 65 5C 8 130 7D 10 200 Male thread type One-touch tting type Symbol Applicable tubing O.D.
Size/Port: 5C [Plug-in Type, Port Size: ø8, Flow: 130 L/min (ANR)]
Fitting Type: B (Branch Tee), Size Combination: 5C (Tubing: 3/4" x 5/8"; Thread: 3/4"), Piping Type: F (Female), Thread: R, Rc, Packaging: 1 (Packaging Equivalent to Class M5.5)
Fitting Type: B (Branch Tee), Size Combination: 5C (Tubing: 3/4" x 5/8"; Thread: 3/4"), Piping Type: M (Male)
Fitting Type: B (Branch Tee), Size Combination: 5C (Tubing: 3/4" x 5/8"; Thread: 3/4"), Piping Type: M (Male), Thread: N (NPT), Packaging: 1 (Packaging Equivalent to Class M5.5)
Fitting Type: H (Straight), Size Combination: 5C (Tubing: 3/4" x 5/8"; Thread: 3/4"), Piping Type: F (Female), Thread: N (NPT), Packaging: 2 (Packaging Equivalent to Class M3.5 w/PVDF Nut)