CLK1

If driving a load such as a relay that generates a surge voltage, use a switch with a built-in contact protection circuit or use a contact protection box.

LEF-OM002xx

LEFS16A-100 NPN (2) Check Parallel I/O configuration matches (NPN or PNP). (2) 17 - 2.4 Construction In-line mouting type A-A LEFS16, 25, 32 A B A LEFS40 A-A A B A Roller type seal band stpper Parts list Description Material Note Description Material Note 1 1 13 Motor cover Aluminum alloy Anodized Body Aluminum alloy Anodized 14 End cover Aluminum alloy

SY3000/5000/7000/9000 Series (Pilot Valve:V100)

screws a.

JSY1000/3000/5000 Series (Non Plug-in)

Actuator drive When an actuator, such as a cylinder, is to be driven Provide ventilation when using a valve in a confined area, such as in a closed control panel.

Electric Actuator / Slider Type 《 AC Servo Motor 》

A C A-A A B B A Auto switch mounting bracket A-A B-B Dust seal band type Seal band holder roller specification C No.

48

7 u A A A-A (LEL25LT-n) A-A (LEL25MT-n) !9 !9 t @0 @1 !0 !6 !8 !5 o Component Parts Description No.

CM2

Use caution to the popping of a snap ring. When replacing rod seals and removing and mounting a snap ring, use a proper tool (snap ring plier: tool for installing a type C snap ring). Even if a proper tool is used, it is likely to inflict damage to a human body or peripheral equipment, as a snap ring may be flown out of the tip of a plier.

SYJ Series

Detaching To detach a socket from a connector, pull out the lead wire while pressing the sockets hook with a stick having a thin tip (approx. 1 mm).

FILTER REGULATOR

Rc Rc C3SF-J-A C3SF-A G G C3SFF-J-A NPT C3SF(-Z)-A NPT C3SFN-J(Z)-A B B External B Semi-standard 6 Semi-standard 6J appearance drawing and Port thread Port thread Part no. Part no. part no. Rc Rc C3SF-6J-A C3SF-6-A G G C3SFF-6J-A NPT C3SF-6(Z)-A NPT C3SFN-6J(Z)-A 1/4 HEX17 Option Semi-standard Semi-standard W Port thread Part no.

FILTER REGULATOR

Rc C2SF-J-A Rc C2SF-CJ-A G C2SFF-J-A G C2SFF-CJ-A External NPT C2SFN-J(Z)-A NPT C2SFN-CJ(Z)-A B B appearance drawing and Semi-standard 6J Semi-standard 6CJ part no. Port thread Port thread Part no. Part no. Rc C2SF-6J-A Rc C2SF-6CJ-A G C2SFF-6J-A G C2SFF-6CJ-A 1/8 1/8 NPT C2SFN-6J(Z)-A NPT C2SFN-6CJ(Z)-A HEX14 HEX14 Option Semi-standard Semi-standard 2 Semi-standard 2J Part no. Part no.

CRJ

Although a zener diode for surge protection is connected at the output side of a solid state auto switch, damage may still occur if the surge is applied repeatedly. When a load, such as a relay or solenoid, which generates surge is directly driven, use a type of switch with a built-in surge absorbing element. 8.

3

A G i 2 x P Port size G A 2 x P Port size b B Conduit DIN terminal D F Q S Cable 6 to 12 G1/2 F Q 280 D G1/2 45 (42) (44) 31.5 Built-in full-wave rectifier type R C C R E J J E 2 x M depth 5 H 2 x M depth 5 B B1 H G A G A B B1 2 x P Port size 2 x P Port size Bracket mounting hole a1 (VXS23, 25) a a1 (VXS24, 26) 6.5 10.5 Dimensions (mm) Model Port size P A B B1 C D E F G H J M Bracket mounting

HRX-OM-X027

Facility having a small installation area (that can not vent the air naturally) Make a forced air exhaust vent on a wall at a high level and an air vent on a wall at a low level.

PFxx-OMX0002

Caution Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Warning Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Danger Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury. Warning 1.

Digital Pressure Switch

The set values for OUT1 are displayed in auto-preset mode as follows: Normal output Reversed output P_1 = A-(A-B)/4 n_1 = B+(A-B)/4 A = Max. pressure H_1 = (A-B)/2 H_1 = (A-B)/2 B = Min. pressure The set values of OUT2 become as follows "_", i.e. "P_2", "n_2", "H_2".

HRL

Use this as a reference.

Digital Pressure Switch

Normal output Reversed output P_1 = A (A B)/4 n_1 = B + (A B)/4 A = Maximum pressure H_1 = (A B)/2 H_1 = (A B)/2 B = Minimum pressure In the OUT2 setting, the above P_1, n_1 and H_1 will be P_2, n_2 and H_2 respectively.

PFxx-OMU0002

Caution Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Warning Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Danger Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury. Warning 1.

CUJ

Although a zener diode for surge protection is connected at the output side of a solid state auto switch, damage may still occur if the surge is applied repeatedly. When a load, such as a relay or solenoid, which generates surge is directly driven, use a type of switch having a built-in surge absorbing element. 8.

VZS

Single solenoid type A side solenoid Black: A Red: COM Double, 3 position type A side solenoid Black: A Red: COM Valve B side solenoid White: B Red: COM Lead wire color Lead Wire Color Single solenoid type A side solenoid Black: A Red: COM Double, 3 position type A side solenoid Black: A Red: COM Valve (1) B side solenoid White: B Red: COM Lead wire color Lead wire length: 0.6 m 3-7-4 5 Series