MGP-OM0242Q M5 After tightening by hand, tighten additional 1/6 to 1/4 rotation with a tightening tool Tapered thread for Rc port (MGP) and NPT port (MGPTN) Use the correct tightening torques listed below. Before tightening the plug, wrap pipe tape around it.
Solid sphere Position of rotational axis: Through the center of diameter r 2 2 r I = m5 27 - Kinetic energy Table 9 shows the allowable kinetic energy of the rotary table.
Take note that the leakage voltage will increase when a resistor is used in parallel with switching element or when a C-R circuit (surge voltage suppressor) is used for protecting a switching device because of the passing leakage voltage through the C-R circuit. The suppressor residual leakage voltage should be 3% or less of the rated voltage. 7.
Leakage voltage Take note that the leakage voltage will increase when a resistor is used in parallel with a switching element or when a C-R circuit (surge voltage suppressor) is used for protecting a switching device because of the leakage voltage passing through the C-R circuit. The suppressor residual leakage voltage should be as follows. DC coil 3% or less of the rated voltage 6.
Solid sphere Position of rotational axis: Through the center of diameter 2 2 r I = m5 27 - Kinetic energy Table (9) shows the allowable kinetic energy of the rotary actuator. The end angular speed is obtained by: Table 9.
Bore size (mm) 32 40, 50, 63 80, 100 Thread size M2.5 X 0.45 X 25 l M3 X 0.5 X 30 l M5 X 0.8 X 40 l Pulling force 4.9N 10N 24.5N Stroke (mm) 2 3 3 e Release lock when mounting or adjusting the cylinder. If mounting is done with lock engaged, lock mechanism may be damaged. * Remove bolt under normal operations.
Snap ring Spring steel Aluminum alloy 6 18 Anodized End plate Rod seal NBR Aluminum alloy 7 19 Hard chrome plated Non-rotating rod Piston seal NBR Stainless steel 8 20 Bushing O-ring A NBR Resin 9 21 Bushing (for non-rotating rod) O-ring B NBR Lead-bronze casting 10 22 Bumper O-ring C NBR Urethane rubber 11 23 Nickel plated Electroless nickel plated Reinforcement ring Hexagon socket head
Turn the oven ON when the temperature reaches 110 degrees C and OFF when the temperature reaches 125 degrees C. Alternate: Alternate turning your output device "ON" and "OFF" from the same Input. Real Time Clock (RTC): The Y2K compliant RTC can control up to 160 time/date combinations. Simply set your outputs to function daily, weekly, monthly or set operations by a calendar date.
Series ZMA How to Order ZMA 07 1 H K 5 T14 C Nozzle diameter Switch lead wires (connector type) 0.5mm 0.7mm 1.0mm 1.3mm 1.5mm 05 07 10 13 15 Lead wire length 0.6m Lead wire length 3m Without lead wires C CL CN Switch type Body type Without 1 point setting/analog output 3 rotations, NPN output T14 For single type Common SUP for manifold Individual SUP for manifold 1 3 5 Without 1 point setting
Guide type C Cam follower guide Number of auto switches Bore size 16 25 40 16 mm 25 mm 40 mm 2 pcs. 1 pc. n pcs. Nil S n Auto switch Thread type Nil Without auto switch (Built-in magnet) Refer to the table below for the applicable auto switch model.
Rotary Cylinder Series MRQ Size: 32, 40 How to Order 32 MRQ B S 50 C A J79W Made to Order or port type Refer to page 343 for the Made to Order details. Nil XF Rc 1/8 G 1/8 NPT 1/8 XN The combination with Made to Order is not available.
ow 0.2 0.3 0.4 0.2 0.2 0.3 0.1 0.2 0.1 0.2 C and b values are for controlled ow with the needle fully open and free ow with the needle fully closed.
0.2 0.1 0.2 C and b values are for controlled ow with the needle fully open and free ow with the needle fully closed.
Fittings & Tubing Air Cylinders Rotary Actuators How to Order Clean series 10 11 Relief type Vacuum suction type Built-in magnet D With auto switch Bore size (mm) 10 C D U 16 30 D M9B 21 C D U 16 30 D M9B Cylinder stroke (mm) Copper, fluorine and silicone-free + low particle generation Number of auto switches 2 pcs. 1 pc. n pcs.
10-/1121-/22Series CJ2 Air cylinder / 6, 10, 16 How to Order Cushion Clean Series 10 11 Relief type Vacuum suction type Rubber bumper (Standard) Air cushion (except 6) Nil A 10 D L 16 60 A R C J 2 H7B 21 D L 16 60 C J 2 H7B R Mounting style Head cover port location Basic style Axial foot style Rod side flange style Symbol Bore size (mm) B L F 6 10,16 Perpendicular to the cylinder axis Nil
CJ2-Z Series 10, 16 Air Cylinder 10-/1121-/22RoHS How to Order Cushion Clean series 10 11 Relief type Vacuum suction type Rubber bumper (Standard) Air cushion Nil A 10 D L 16 60 A R C J 2 M9BW Z B 21 D L 16 60 R C J 2 M9BW Z B Number of auto switches Nil Built-in magnet Head cover port location 2 pcs. 1 pc. n pcs.
) Not available for 30 Cushion Nil Without auto switch (Built-in magnet cylinder) Nil C Without air cushion With air cushion on both ends For the applicable auto switch model, refer to the table below.
CJ2-Z Series Air Cylinder/10, 16 10-/1121-/22How to Order Cushion Clean series 10 11 Relief type Vacuum suction type Rubber bumper (Standard) Air cushion Nil A 10 D L 16 60 A R C J 2 M9BW Z B 21 D L 16 60 R C J 2 M9BW Z B Number of auto switches Nil Built-in magnet Head cover port location 2 pcs. 1 pc. n pcs.
q Body size 20 30 40 50 60 Symbol Description w Pipe thread type Nil Metric thread (M5) Rc N Note 1) NPT F Note 2) G + 01 1/8 02 1/4 03 3/8 04 1/2 06 3/4 10 1 + e Port size Option a Mounting Nil Without mounting option B Note 3) With bracket + r Nil Polycarbonate bowl 2 Metal bowl 6 Nylon bowl 8 Metal bowl with level gauge C With bowl guard Note 6) Note 6) Note 6) Note 6) b Bowl 6C
Operating temperature range (C) 5 to 60 The shock absorber service life is different from that of the MY1W cylinder depending on operating conditions. Refer to the RB Series Specific Product Precautions for the replacement period. Technical Data 1351 A