Hand Valve Series VH 4 (B) 25 25 25 4 (B) 1 (P) 3 (R) 1 (P) 62 74 49 62 2 (A) 4-5.5 4-6.6 49 62 125 134 94 97 92 73 106 1 (P) 88.5 23 3 (R) 1 (P) 3 (R) 12 12 27 4-Rc1/4 13.5 4-Rc1/4, 3/8 VH32l-02 to 03 (Bottom piping) 2 (A) 44 3 (R) 1 (P) 4-Rc1/4, 3/8 4 (B) 3.6-9 Hand Valve Series VH Body Mounted/Dimensions VH40l-02 to 04 VH40l-06 4 (B) 2 (A) 4 (B) 2 (A) 25 25 1 (P) 3 (R) SlA 1 (P) 3 (R) l102 102 88 89
Cable length (L) 003 0.3 [m] Connector Setting Power supply for input and control: 24 VDC 10% Power supply for solenoid valves: 24 VDC +10%/-5% Power supply voltage range SSPS Socket side: Straight Plug side: Straight 005 0.5 [m] Power supply for input and control: 6.2 A (GW unit internal current consumption: 200 mA or less) Power supply for solenoid valves: 4 A 010 1 [m] SAPA Socket side
All electrical work must be carried out in a safe manner by a qualified person in compliance with applicable national regulations. atmosphere. Do not mount in a location exposed to radiant heat.
Therefore, a speed of 500mm/s is equivalent to 5kcps (kHz), but a counting speed 2 to 3 times greater is recommended for actual operation.
Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Caution: Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Warning: Danger : Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury.
(ZS-24-A/ZS-35-A) B *(ZS-24-D) C D + F02 ISO228-1 1 *1 L M SI*2 P (psi)*1 1 2 ISE80H: MPa MPa kpa N NPN1 P PNP1 A NPN2 B PNP2 R NPN2+/ T PNP2+/ S NPN2+/ V PNP2+/ / ZS-24-A ZS-24-D ZS-35-A ZS-35-C ZS-35-B ZS-35-F ZS-35-E + -9No.PS-OMM0002CN-F LCD (UP) (SET) ) (DOWN) () LCD 4 (UP) ON/OFF (DOWN) ON/OFF (SET) -10No.PS-OMM0002CN-F 2 ON/OFF 2 7 "8"7 "-"()7 digit()
Turn cover A counterclockwise until it stops (approx. 45). 4. Install a new element on cover A and insert it into the case. Cover A Case Cover A Case O L L Element O-ring Window 5.
When installing a paddle on IF3O type, piping may be interfered with by the tip of a paddle. Because this is used to detect a small flow rate, and to narrow the distance between a paddle and piping, additional machining of the paddle tip may be necessary to eliminate interference between the two. 6. Use pipe fittings that comply with JIS specifications.
piLl lanp lighls wh6n hlo swilches a turned ON Eran0e P$s!
Manual override (Non-locking) 23 23 Cylinder ports are NAMUR hole pattern. 3-12-2 NAMUR Interface 5 Port Solenoid Valve Series VFN2000N/3000N NAMUR Mounting Pattern Axis A-A' can be aligned to suit.
OFor high speed and large load applications, the actuator absorbs a large amount ol energy. lt i6 recommended to contact a SMC representative betore selecting type and model to be used lor such loads.
A A Solid state auto switch D-M9B, D-M9N Reed auto switch D-A93 (mm) (mm) Stroke (mm) 20 41 29 47 35 Stroke (mm) 20 45 25 51 31 Auto switch operating range Auto switch operating range 15 40.5 20.5 Model Model 25 50.5 30.5 30 59 39 10 35 15 25 46.5 34.5 30 55 43 10 31 19 15 36.5 24.5 A B A B A B A B A B A B 11-/22-MXP10 11-/22-MXP10 11-/22-MXP12 11-/22-MXP12 3 5 11-/22-
There is a risk of unexpected malfunction. Do not use solvents such as benzene, thinner etc. to clean each unit. They could damage the surface of the body and erase the markings on the body. Use a soft cloth to remove stains. For heavy stains, use a cloth soaked with diluted neutral detergent and fully squeezed, then wipe up the stains again with a dry cloth.
30 55 43 10 31 19 15 36.5 24.5 A B A B A B A B A B A B 11-/22-MXP10 11-/22-MXP10 3 5 11-/22-MXP12 11-/22-MXP12 11-/22-MXP16 11-/22-MXP16 99 Air slide table MXP/MXPJ6 11221122Dimensions / MXPJ6 5 C 11-/22-MXPJ6-5 Depth 2.5 2.5 7 H 5 10.05 3 3.5 4M3 x 0.5 depth 3 +0.030 0 D B 16.5 3.5 18 14 13 20 6 +0.030 0 Depth 2.5 2.5 6 E 5 2-M4 x 0.7 Piping port F QL 6 13.5 Prepared hole diameter 3.3
Because tube fittings are provided, use a tube with a bore of 10mm, and keep the overall pipe length within 5m. AM850 type (N.O) Use a tube with a bore of 9mm or more, and keep the overall pipe length within 2.8m.
Make sure to connect a speed controller and adjust it to a speed of 500 mm/s or less to operate the cylinder.
piLl lanp lighls wh6n hlo swilches a turned ON Eran0e P$s!
4 (B) 25 25 25 4 (B) 1 (P) 3 (R) 74 1 (P) 62 62 49 2 (A) 45.5 46.6 49 62 125 134 94 97 92 73 106 1 (P) 88.5 23 3 (R) 1 (P) 3 (R) 12 12 27 4-1/4NPT 13.5 4-1/4,3/8NPT VH32 -N02/N03 (Bottom porting) 2 (A) 44 3 (R) 1 (P) 4-1/4,3/8NPT 4 (B) 5 Series VH Body Mount/Dimensions (mm) / Body mount type Dimensions VH40 -N02/N03/N04 VH40 -N06 Scale: 35% 4 (B) 2 (A) 4 (B) 2 (A) 25 25 1 (P) 3 (R) 1 (P
Make sure to connect a speed controller and adjust it to a speed of 500 mm/s or less to operate the cylinder.