Digital Flow Switch ZS-46-B Panel mount adapter ZS-46-D Panel mount adapter + Front protection cover ZS-46-5L Power supply/output connection lead wire 5-core, 2 m ZS-27-01 Front protection cover B Panel mount adapter Connection Example ZS-46-B PFG300 Sensor connector D Panel mount adapter + Front protection cover PF3A7 H Power supply/output connection lead wire ZS-46-D Lead wire and M12 connector (Option for
Note 4) F, P, T and S kits are provided with an exhaust on one side, while C kits are with an exhaust on both sides. The number of max. stations differs from kit to kit. (Refer to the table below.)
The rotation range under the adjustment of an angle at 60 is indicated below.
There is no mounting interchangeability with serise CA2. 6-6-46
Do not apply strong impact or an excessive moment while mounting the product or a workpiece. LEC SS-T LEC Y LEC Y If an external force over the allowable moment is applied, it may cause play in the guide or an increase in the sliding resistance. 3.
Note) Since the electrical entry is LO, select an appropriate connector assembly part no.
Note) Please contact SMC when using an individual EXH spacer assembly, an individual SUP spacer assembly, an adapter plate assembly, or an interface regulator on 41P and 43P types.
7 Made to order common specifications 5.4-46 -XC11 Dual stroke cylinder/Single rod !8 5.4-52 -XC12 Tandem cylinder !
Never use in an atmosphere of explosive gases. The structure of auto switches is not intended to prevent explosion. Never use in an atmosphere with an explosive gas since this may cause a serious explosion. 2. Do not use in an area where a magnetic field is generated. Auto switches will malfunction or magnets inside cylinders will become demagnetized.
Do not use an air cylinder as an airhydro cylinder. If it uses turbine oil in place of fluids for cylinder, it may result in oil leakage. 5. Combine the rod end section, so that a rod boot might not be twisted. If a rod boot is installed with being twisted when installing a cylinder, it will cause a rod boot to fail during operation.
The rotation range under the adjustment of an angle at 60 is indicated below.
In such a case, carry out an adsorption test for confirmation. The vacuum pressure when using an ejector is approximately 60 kPa as a guide. The theoretical lifting force of a pad can be found by calculation or from the theoretical lifting force table.
46 43 27 48 46 46 Stroke 100 to 150 A Shock absorber at extension end Max. 35 Shock absorber at retraction end Dimensions not indicated are the same as basic type.
With an ejector When a few air cylinders are locally used.
The graphs are based on operation using an SMC DC power input type driver with halfstep energization.
Note 1) This cylinder cannot perform an intermediate stop using an air pressure circuit in vertical operation. In this case, an intermediate stop can be performed only by using an external stopper, etc. Note 2) Made-to-order products should be considered, too, depending on an operating environment, etc.
Therefore, if the actuator motor is used in an environment where strong magnetic fields are present, malfunction or failure may occur. Do not expose the actuator motor to magnetic fields with a magnetic flux density of 13 mT or more. When installing an electric actuator and an air cylinder with an auto switch (ex.
How to Order Type 46 (5 Port/Base mounted) Applicable solenoid valve SYJ340SYJ343SS5YJ3 46 05 M5 Type 46 Type S46 ( ) Single solenoid coil is on same side as the A, B port. M5 x 0.8 R1 R2 port Applicable blanking plate assembly SYJ3000-21-2A Stations Valve mounting direction 02 2 stations Single solenoid coil is on opposite side as the A, B port.
error in unit 0. 1 There is an error in unit 1. 2 There is an error in unit 2. 3 There is an error in unit 3. 2 4 There is an error in unit 4. 5 There is an error in unit 5. 6 There is an error in unit 6. 7 There is an error in unit 7. 0 There is an error in unit 8. 1 There is an error in unit 9. 2 Reserved 3 Reserved 3 4 Reserved 5 Reserved 6 Reserved 7 Reserved : The data of diagnostic
Use caution, because an external action such as an impacting load, strong vibration or turning force, may damage the locking mechanism or reduce its life. 20Data Stop signal Amount of overrun 6-12-29 30 Series C95N Specific Product Precautions 2 Be sure to read before handing. Adjustment Pneumatic Circuit Mounting Warning Warning Warning 2. Do not apply an offset load to the piston rod.