1 Model HTB 1 8 Rc CY1S20 CY1S25 CY1L25 CY1S32 CY1L32 CY1S40 CY1L40 20 20 7.5 20 20 7.5 1 8 Rc 20 23 8.2 24 24 7.5 1 8 Rc 26.5 26.5 8.2 25 25 8 1 4 Rc 30.5 30.5 11 Dimensions except mentioned above are the same as standard type of Series CY1B. Refer to page 8-15-24.
.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com 4 Electric Actuator with Integrated Guide Series LTF Lead screw lead mm Mounting orientation Motor type Series Page Model Guide type Ground ball screw Rolled ball screw 6 10 20 10 20 10 20 10 20 6 10 20 10 20 10 20 10 20 LTF6 LTF8 LTF6 LTF8 LTF6 LTF8
Same as cushion seal A except for 20, 25 standard strokes Steel ball B Carbon steel 21 Cushion seal B Urethane 57 Tooth ring Stainless steel 22 Damper Urethane Cushion ring gasket A NBR 58 23 Same as cushion ring gasket A except for 20, 25 standard strokes C type snap ring for taper ring Carbon steel 24 Cushion ring gasket B NBR 59 C type snap ring for unlocking cam shaft Carbon steel 25
When using as a stopper, select a model with a stroke of 30mm or less for bore sizes 20 and 25, and 50mm or less for bore sizes 32 to 100.
When using as a stopper, select a model with a stroke of 30mm or less for bore sizes 20 and 25, and 50mm or less for bore sizes 32 to 100.
Pad Caution Guide for drop prevention Provide an auxiliary device (example: a guide for preventing the workpieces from dropping) as necessary. Mounting Position As a rule, the unit must be installed horizontally.
Use caution, as operating above the prescribed values may lead to dropping of the load. The cushion effect (smooth start-up, soft stop) exists only before the stroke end in the stroke ranges indicated in the table below. The cushion effect (smooth start-up, soft stop) cannot be obtained in an intermediate stop or return from an intermediate stop using an external stopper, etc.
As a result, the inside of the bowl q is shut off from the outside air. Therefore, even if there is an accumulation of condensate in the bowl q, it will not drain out.
Combination Symbol: K2 Combination Symbol: K7 An N.C. solenoid valve is used as the supply valve. Also, an external 2 port valve (vacuum valve) must be provided to serve as the vacuum release valve. An air operated N.O. valve is used as the supply valve. An N.C. solenoid valve is used for the vacuum release valve.
This product cannot be used as a check regulator by installing it between solenoid valve and actuator. 3. Port with a pressure gauge or a plug can be used as an OUT port.
an inertial load. ( ) 1 2 3 7 10 20 30 50 70 100 200 (Example) Clamp F: Pressing force (N) l Static torque calculation Ts = F x l (Nm) Shaft center Note) Effective torque values are representative values and not to be considered as guaranteed values.
Mixed single and double wiring are available as an option.
Also, applicable for use in an environment with water splashing such as food processing and car wash equipment, etc.
/25 REAH15/20/25 REAH15/20/25 REAH15, 20 REAH15, 20 REAH25 REAH15, 20 REAH25 0.08 0.03 REAH25 Deflection (mm) Deflection (mm) Deflection (mm) Deflection (mm) 0.02 0.06 0.02 0.04 0.01 0.01 0.02 5 10 15 20 0 25 25 25 5 10 15 20 0 Moment (Nm) 5 10 15 20 0 Moment (Nm) Moment (Nm) REAHT25/32 REAHT25/32 REAHT25/32 0.05 REAHT25 REAHT25 REAHT32 REAHT32 REAHT25 0.03 Deflection (mm) Deflection (mm)
Do not use an air cylinder as an airhydro cylinder. If it uses turbine oil in place of fluids for cylinder, it may result in oil leakage. 4. The oil stuck to the cylinder is grease. 5. The base oil of grease may seep out.
When designing an application, be sure to allow sufficient clearance for maintenance and inspections. x 1000 Auto switch operating range (mm) V(mm/s) = Time load applied (ms) In cases of high piston speed, the use of an auto switch (D-F5NT) with a built-in OFF delay timer (approx. 200ms) makes it possible to extend the load operating time. 4. Wiring should be kept as short as possible.
In this example, one preset of the CEU5 performs the same function as two presets of an ordinary counter. +0.05 0.02
OFF: Position data is handled as an absolute value. ON : Position data is handled as an incremental value.
As the circulating fluid temperature at this time is 20 oC, "AS.06" starts alarm monitoring at the same time as the operation start. Status (2): The circulating fluid temperature becomes within the set range of "AS.04", and starts "AS.04" alarm monitoring.