HRX-OM-W060 The product operation at the time of alarm AL21 can be selected. This function is set to [ ] (stop) at the time of alarm by default.
Flat wlth rib 1 0 1 2 21 29.946 5 6 1 . 7 1 3 1 5 't2 21 29.946 5 6 3 1 . 8 '19 20 1 6 1 8 12.5 215t301 46.S 5 3.5 Dep type 23 23 22 23 23 22 50 48 50 Applicable Tube 56 54 56 54 57 co 57 '5l3e" lube may be subslituled for 4mm.
Note 1) When using a D-F8 switch, mount it at a distance of 10 mm or more from magnetic substances such as iron, etc. Note 2) Add -61 at the end of the part number for the flexible lead wire.
Note 1) When using a D-F8 switch, mount it at a distance of 10 mm or more from magnetic substances such as iron, etc. Note 2) Add -61 at the end of the part number for the flexible lead wire.
If the mounting part of the body comes loose, tighten at the specified torque. For the recommended torque, please refer to the table below.
Consult SMC concerning water resistance, elasticity of lead wires, and usage at welding sites, etc. 23 Series RQ Specific Product Precautions Be sure to read before handling. Refer to pages 17 through 23 for safety instructions, actuator precautions and auto switch precautions. Installation and Removal of Snap Ring Caution Selection Caution 1.
Test was performed at both energized and de-energized states in the axial direction and at the right angles to the main valve and armature.
Symbol: C8 Symbol: C9 Symbol: C10 Angle adjustment at the rotation starting point and the end point are at 5. Rotating range is changed. Rotation angle is at 90 10. The rotation starting point is on the perpendicular line (down). Angle adjustment at the rotation starting point and the end point are at 5. Rotating range is changed. Rotation angle is at 90 10.
Test was performed at both energized and de-energized states in the axial direction and at the right angles to the main valve and armature. (Values at the initial period) Note 4) Based on JIS C 0920. Note 5) Based on JIS C 4003.
Active face A (upper switch) becomes covered at open limit of travel and face K (lower switch) at closed limit.
Be certain to turn on the power when the flow rate is at zero. Allow an interval of 10 minutes after turning on the power, as there are some changes in the display. 5. Flow rate unit Switch measures at mass flow rates without being influenced by temperature and pressure.
Without Air Cushion Port Cushion valve Double clevis style (D) CDH10 Bore size (mm) Z ZZ 32 40 50, 63 80, 100 170.5 160 164 190 238 175 205 Double Clevis Style 261 U Bore size (mm) Stroke range CDH10 CX +0.3 +0.1 CZ L RR U Z ZZ L Z + Stroke RR CX 32 40 50 63 80 100 Up to 500 23 23 30 30 42 42 10.5 11 15 15 23 23 13 13 17 17 26 26 28 28 40 40 60 60 154 158 182 182 228 228 164.5 10 10 14
Without Air Cushion Port Cushion valve Double clevis style (D) CDH10 Bore size (mm) Z ZZ 32 40 50, 63 80, 100 170.5 160 164 190 238 175 205 Double Clevis Style 261 U Bore size (mm) Stroke range CDH10 CX +0.3 +0.1 CZ L RR U Z ZZ L Z + Stroke RR CX 32 40 50 63 80 100 Up to 500 23 23 30 30 42 42 10.5 11 15 15 23 23 13 13 17 17 26 26 28 28 40 40 60 60 154 158 182 182 228 228 164.5 10 10 14
Fine lock series (Series CLJ2/CLM2/ CLG1) Maximum load at horizontal mounting: 70% or less of the holding force (Maximum static load) for spring lock Maximum load at vertical mounting: 35% or less of the holding force (Maximum static load) for spring lock Lock-up series (Series CL1) Maximum load at horizontal mounting: 50% or less of the holding force (Maximum static load) Maximum load at
Note 2) The above values should be used as a guide for detection at stroke end.
Cylinder port is located at U side of body.
(Values at the initial period) Vibration resistance: No malfunction occurred in a one-sweep test between 45 and 2000 Hz. Test was performed at both energized and de-energized states in the axial direction and at the right angles to the main valve and armature.
(Only auto switch mounting brackets are packed assembled.) 333 CHSD Series Specifications 40 50 63 80 100 Bore size (mm) Double Acting: Single Rod Action General mineral hydraulic fluid Fluid 10 MPa Nominal pressure 12 MPa Maximum allowable pressure 15 MPa Proof pressure 0.25 MPa With pressure at front side Minimum operating pressure 0.15 MPa With pressure at rear side -10 to 80C Without
a sensing position, and the green indicator light goes on at the position of maximum sensitivity.
Fig. 14 Install the stopper at a sufficient distance from the table centre.