Table of Contents ) L1 = 50 [mm] L2 = 40 [mm] m L2 L1 Item Load factor an Note 1.
The dimension is added by 21 mm at 1 piece addition.
Dimensions Space saving branch tee: LQ3T-SB Metric Size (L2, L2) 2 x B Model Applicable tubing O.D.
The average speed of the cylinder is obtained by dividing the stroke by the total stroke time.
Simple and unencumbered appearance by adopting roundshaped cord. How to Order 2. Do not use a tool to mount the connector, as this may cause damage. Only tighten by hand. (0.4 to 0.6N) SY100-68-A 3. Do not apply excessive power greater than 30N to the connector cable, otherwise IP65 cannot be satisfied.
Applicable shaft type: K Equal dimensions are indicated by the same marker. Machine female threads into the short shaft. The maximum dimension L2 is, as a rule, twice the thread size. (Example) For M4: L2 = 8 Applicable shaft types: J, Z The long shaft can be further shortened by machining it into a stepped round shaft.
Average speed of cylinder is obtained by dividing the full stroke time by the stroke.
/60 Hz) PLC (Positioning unit/Motion controller) Power supply for I/O signal 24 VDC Provided by customer L1 External regenerative resistor Page 106 L2 L3 If the external regenerative resistor is required, it should be provided by the customer.
by means of the ON input.
Applicable shaft types: J, K, T (mm) (mm) L2 + (3 x P) L2 = L2 + (3 x P) L2 = Q1 Q2 Shaft type Shaft type J K T J K T Q1 = M Size Size L1 + (3 x P) L1 = 10 10 Not available Not available M3 M3 15 15 M3, M4 M3, M4 20 20 Q2 = M Q2 = M M3, M4, M5 M3, M4, M5 30 30 K axis (T axis) J axis M3, M4, M5 M3, M4, M5 40 40 Symbol: A37 The long shaft can be further shortened by machining it into a stepped
The short shaft can be further shortened by machining it into a stepped round shaft with male threads. (If shortening the shaft is not required, indicate * for dimension Y.) CRB2 CRB2 Q1 = M L2-(3 x P) CA = C CRB1 Y = Applicable shaft type: W Applicable shaft type: W L2 = MSU CB = C Equal dimensions are indicated by the same marker.
EtherCAT is registered trademark and patented technology, licensed by Beckhoff Automation GmbH, Germany. 278
The average velocity of the cylinder is what the stroke is divided by the total stroke time.
Lock ring Turn the lock ring in the locking direction as shown by the arrow. Orange Calculation of Dimensions When Plug and Socket are Connected Overall length B when plug and socket connected = Plug (L1 L2) + Socket (L2) + 0.5 Plug Socket Example) Overall length of KK3P-01MS (plug) and KK3S-01MS (socket) when they are connected.
Has large retaining force while holding force is increased by the collet.
Applicable shaft types: J, X, T W1 = L1 = L3 = X = W2 = L2 = L4 = Y = (mm) (mm) W2 L2 max Y Y Y Y Y W1 L1 max X 2 X 2 X 2.5 X 3 X 3 L4 max L2 1 L2 1 L2 2 L2 2 L2 2 Y 4 to 18 4.5 to 20 6.5 to 30 8.5 to 32 9.5 to 36 L3 max L1 1 L1 1 L1 2 L1 2 L1 2 Size 10 15 20 30 40 X 6 to 18 6.5 to 20 9.5 to 30 11.5 to 32 12.5 to 36 Size 10 15 20 30 40 0.5 to 1.5 0.5 to 1.5 1 to 2 1 to 2 1
The average velocity of the cylinder is what the stroke is divided by the total stroke time.
n Dimensions 8 263 276 L1 L2 7 238 251 8 263 276 L1 L2 6 213 226 7 238 251 5 188 201 6 213 226 4 163 176 5 188 201 3 138 151 4 163 176 1 2 113 126 3 138 151 1 2 113 126 88 101 88 101 L n L n 9 288 301 15 463 476 14 413 426 13 388 401 12 363 376 11 338 351 10 313 326 9 288 301 16 463 476 15 463 476 14 413 426 13 388 401 12 363 376 11 338 351 10 313 326 16 463 476 L1 L2 L1 L2 2-5-37 Base Mounted
Main parts Controller Note) The speed is limited by the transfer load. Refer to the maximum speeds for each transfer load on the next page.