Series CQ2

Take measures to prevent freezing, since moisture in circuits will be frozen under 5C, and this may cause damage to seals and lead to malfunction. Refer to SMCs Air Cleaning Equipment catalog for further details on compressed air quality. Piping Caution 1.

Slide Tables MX Series

Caution 1.Do not use in atmosphere where the actuator is in direct contact with liquid such as cutting oil. 1.

CUJ

1 3 10mm or more Note 1) Solid state switch: D-F9 includes one auto switch.

Hand Valve Series VH

(R) 1 (P) 1 (P) 25 17 2 4-Rc1/4, 3/8, 1/2 4-Rc3/4 VH43l-02 to 04 (Bottom piping) VH43l-06 (Bottom piping) 2 (A) 2 (A) 46 54 1 (P) 3 (R) 1 (P) 3 (R) 4 (B) 4 (B) 4-Rc3/4 4-Rc1/4, 3/8, 1/2 3.6-13 Hand Valve Series VH Precautions Be sure to read before handling.

Ejector Valve Unit Series ZYY/ZYX 1

Series ZYX3000 Series ZYY3000 13-8-1 2 Electronic Pressure Switches Precautions 1 Be sure to read before handling. Wiring Design & Selection Warning Warning 1. Confirm wire colors and terminal numbers when wiring is performed.

Low torque Metal seal type Rotary joint

or less 0.05 Nm or less 0.10 Nm or less 0.20 Nm or less Allowable rotation speed 3000 min-1 (r.p.m.)Note 3) 2000 min-1 (r.p.m.) 1500 min-1 (r.p.m.) 900 min-1 (r.p.m.) 600 min-1 (r.p.m.)

MIW/MIS

Work piece weight (kg) Work piece weight (kg) 10 10 5 5 1 1kg 1 0.25kg 0.1 10 20 40 0.1 5 10 20 30 Transfer speed (m/min) Transfer speed (m/min) 32.5m/min 12m/min Procedure3 Confirmation of allowable lateral load MIW12 MIS12 1. Calculation of applied lateral load F F = N m g (N) = 0.2 x 10 x 0.1 x 9.8 = 2.1 (N) 1.

ZSE30/ISE30

To use a peak hold function, press and hold the UP button for 1 second or longer. The maximum pressure value is held and blinks repeatedly. Press and hold the UP button again for 1 second or longer to release this function and return to the measuring mode. To use a bottom hold function, press the DOWN button for 1 second or longer.

Magnet Gripper for Collaborative Robots

Product Specifications 3-1. How to order 8 - 3-2.

ZPT/ZPX

1 2 3 5 8 0 0 0 1 1 3 5 8 16 27 53 84 1 0 0 1 1 0 ZCU AMJ Misc.

Ｍ agnet Gripper Unit for Collaborative Robots

Product Specifications 3-1. How to order MHM-25D-X7400A-ASSISTA(-P) 6 - 3-2.

Magnet Gripper Unit for Collaborative Robots

Product Specifications 3-1.How to order 6 - 3-2.

Safety Instructions

Chamfered port size D (Recommended value) Rc, G NPT, NPTF Female thread size 1 8 1 4 3 8 1 2 10.5 to 11.8 14.1 to 15.8 17.4 to 19.4 21.7 to 25.1 10.2 to 11.8 13.6 to 15.8 17.1 to 19.4 21.4 to 25.1 15-1-11

Ｍ agnet Gripper Unit for Collaborative Robots

They are all important notes for safety and must be followed in addition to International Standards (ISO/IEC)*1) , and other safety regulations. *1) ISO 4414: Pneumatic fluid power -General rules relating to systems. ISO 4413: Hydraulic fluid power -General rules relating to systems. IEC 60204-1: Safety of machinery -Electrical equipment of machines.

Magnet Gripper Unit for Collaborative Robots

They are all important notes for safety and must be followed in addition to International Standards (ISO/IEC)*1) , and other safety regulations. *1) ISO 4414: Pneumatic fluid power -General rules relating to systems. ISO 4413: Hydraulic fluid power -General rules relating to systems. IEC 60204-1: Safety of machinery -Electrical equipment of machines.

Two Hand Control Valve

Mandrel = LD 2d 1 x 100 Here, : Deformation ratio (%) d: Tube diameter (mm) L: Measured length (mm) D: Mandrel diameter (mm) (Twice against the minimum bending radius) Test temperature: 20 5C Relative humidity: 65 5% Air Supply Warning 5.Do not use fluids other than specified. The only fluid that can be used is air. 1. Use clean air.

Cylinder Positioner IP200 Series

How to Order 100 IP200 Applicable stroke 25 to 300 mm * Manufacture of strokes in 1 mm increments is possible. Specifications (No load) Note 1) Replacement Parts Supply pressure 0.3 to 0.7 MPa Input pressure 0.02 to 0.1 MPa Part no.

Clean Exhaust Filter SFE Series

Clean Exhaust Filter SFE Series RoHS How to Order SFE 11 Size/Port size Male thread type Plug-in type Symbol Port size Max. ow capacity L/min (ANR) 11 M5 x 0.8 3 42 R1/8 65 52 R1/8 130 53 R1/4 130 73 R1/4 200 Symbol Port size Max. ow capacity L/min (ANR) 3A 4 30 4B 6 65 5C 8 130 7D 10 200 Male thread type One-touch tting type Symbol Applicable tubing O.D.

Fitting Type: L (Elbow), Metric Size, Side A: No (Select Inch Size, Side A), Inch Size, Side A: 5C (Tube O.D. 3/4", Tubing Size 3/4"x5/8"), Metric Size, Side B: No (For Types H and L, and Types B or R w/Same Tubing Size), Inch Size, Side B: No (For Types H and L, and Types B or R w/Same Tubing Size), Piping: M (Male), Thread: R, Rc, Packaging: 1 (Standard Packaging Equivalent to Class M5.5

Fitting Type: B (Branch Tee), Size Combination: 5C (Tubing: 3/4" x 5/8"; Thread: 3/4"), Piping Type: F (Female), Thread: R, Rc, Packaging: 1 (Packaging Equivalent to Class M5.5)