PF3A7xxH.eng When the output is ON: Orange LED is ON. (4) Press and hold the S button for 2 seconds or longer to complete the OUT setting. (If the button is pressed for less than 2 seconds, the setting will be returned to P.)
Immediately after supplying power, there is drift of about 0.5% F .S. When used with very low pressure, allow the unit to warm up for about 20 to 30 minutes. MPa 2. Do not use in locations where there is splashing or spraying of oils and solvents. 3. When using a commercially available switching regulator, be sure to ground the FG terminal. OUT2 OUT1 SET 4.
(A.B) 0.15 mm 2(AWG26) 5 (R.T.S.V) 0.95 mm CE UL/CSA RoHS 02 N02 F02 C01 A2 B2 R1/4 NPT1/4 G1/4 Rc1/8 URJ1/4 TSJ1/4 () 117 g 118 g 114 g 120 g 111 g () 89 g 90 g 86 g 86 g 92 g 83 g 110 -5 Pam 3/s 110 -10 Pam 3/s A B C 0.0-101.0kPa 0 -101.0 kPa -100.0100.0kPa -100 kPa 100 kPa -0.1001.000MPa -0.1 MPa 0 1.
Data Setting Warning 1 (Parameter Number Error) A.94B*4 Data Setting Warning 2 (Out of Range) A.94C*4 Data Setting Warning 3 (Calculation Error) A.94D*4 Data Setting Warning 4 (Parameter Size) Warning A.94E*4 Data Setting Warning 5 (Latch Mode Error) A.95A*4 Command Warning 1 (Unsatisfying Command) A.95B*4 Command Warning 2 (Non-supported Command) A.95D*4 Command Warning 4 (Command Interference
Data Setting Warning 1 (Parameter Number Error) A.94B*4 Data Setting Warning 2 (Out of Range) A.94C*4 Data Setting Warning 3 (Calculation Error) A.94D*4 Data Setting Warning 4 (Parameter Size) Warning A.94E*4 Data Setting Warning 5 (Latch Mode Error) A.95A*4 Command Warning 1 (Unsatisfying Command) A.95B*4 Command Warning 2 (Non-supported Command) A.95D*4 Command Warning 4 (Command Interference
setting 25 mm OUT2 White 3 [F 4] Setting of switch output response time 1 s DC(-) Analogue Blue1 Grey 2 URL http://www.smcworld.com [F 5] Select analogue output filter ON Akihabara UDX 15F, 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021, JAPAN Phone: +81 3-5207-8249 Fax: +81 3-5298-5362 [F 6] Setting of security code OFF [F98] Setting of all functions OFF Note: Specifications are subject
When the Pressure switch is to be mounted in a place where water and dust splashes occur, insert a tube (O.D 4, I.D 2.5) into the air-relieving port of the Pressure switch. OFF [F10] Setting of security code Display to show the product OFF [F98] Setting of all functions 1 s OFF [F99] Reset to the default setting Set ON and OFF point of the Pressure switch.
+ + code (ZL3-LW1-P-A) code (ZL3-LW1-N-A) *FUNC *ZSE10ZL3,ZL6 5.2 1) 2) 3), 4) 5)1015 10 1% 6), 7)LCD 8)FG 14 No.ZL3-OM00801-A . 6.1 ON 6.2 1) 2) 3), 4)12 5) 15 No.ZL3-OM00801-A 7 , 7.1 ZL3 ZL3 ZL6 ZL6 14 1 7 15 PBT 2 POM 16 POM 2 3 PBT 17 PBT 4 POM 18 5 FKM 6 PBT 19 7 PBT 3 6 8 1 PBT 20 , 9 1 4 1 10 2 21 11 2 PBT 5 22 12 POM 8 13 3 O HNBR/NBR
S S S Flow direction (1) Press the SET button once when the item to be changed is displayed on the display. The set value on the sub display (right) will start flashing. The output will not operate for 3 seconds after supplying power. The identification code of the product is displayed.
Display to show the standard product Names of individual parts 1 s Output (OUT1) display (Green) Output (OUT2) display (Red) Display to show the unit specification button (SET) 1 s Connector LED display ZSE10(F)/ISE10 Display to show the product Pin No. of the Connector button (UP) Socket Housing DC(+) Brown 5 Pin No. 1 s button (DOWN) Display to show the pressure range OUT1 Black 4 OUT2
They are all important notes for safety and must be followed in addition to International standards (ISO/IEC) and other safety regulations. 1 s OFF [F 8] Setting of security code OFF [F90] Setting of all functions Display to show the unit specification OFF [F97] Selection of copy function 1 s Normal [F98] Check of output OFF [F99] Reset to the default setting Display to show the product Mounting
X B(ZS-24-B) M45L B -16No.PS-OMM0006CN-E M8(3) (ZS-35-C/ZS-35-D) +(ZS-35-F/ZS-35-G) () ZS-35-C/D -17No.PS-OMM0006CN-E 79 Nm M5 (12mm) 1 2 1) 0.1 mm 2)0.1 mm 3)+0.15 mm -0.2 mm -18No.PS-OMM0006CN-E () TU0425 ( 4 2.5) -19No.PS-OMM0006CN-E (M8(3)22) Z/ISE40A--DC(+) -S/-R () NPN 2 Max.28 V80 mA 1 V R15 V 1 k S420 mA 12 V 300 24 V 600 50 OUT1 OUT2 DC(-) DC(+) -S/-R () NPN 2
Seal: S (Metal), Size: 2 (Size 18mm), Configuration: FG (2-position), Number of Solenoids: S (Single), Voltage: 3 (24VDC), Light/Surge Voltage Suppressor: Z (Indicator Light, Surge Voltage Suppressor), Manual Override: Push Type, Internal/External Pilot: Internal Pilot, CE Compliant: Q (CE Compliant)
Seal: Metal, Size: Size 18mm, Configuration: 2-position, Number of Solenoids: Single, Voltage: 24VDC, Light/Surge Voltage Suppressor: Indicator Light, Surge Voltage Suppressor, Manual Override: Push Type, Internal/External Pilot: Internal Pilot, CE Compliant: CE Compliant
(-) 1 s Display to show the pressure range Thank you for purchasing the SMC ZSE40A(F)/ISE40A Series Digital Pressure Switch.
When using a commercially available switching regulator, be sure to ground the FG terminal. SET 4. In locations where the switch is exposed to water and dust, etc., these may enter the switch from the atmospheric release port. Insert 4 tubing (inside diameter 2.5) into the atmospheric release port, and extend the other end to a safe area where water, etc., is not splashed or sprayed.
PF3WC Integrated type: Straight type 4 Lock ring PF3WS Remote type: Supply type 4 The flow adjustment valve is not designed for applications that require daily and repetitive adjustment. If the valve is adjusted frequently, fluid may leak due to wear of the internal seal.
Mount the product with bracket using M4 screws (4 pcs.) or equivalent. Screw is prepared by customer.
SET button: Press this button to change to another mode and to set a value. 3 Blue DC(-) 3 Blue DC(-) 3 Blue DC(-) Safety Instructions Black OUT1(NPN) Black OUT1 (PNP) Black OUT1 (NPN or PNP) 4 4 4 Refer to the product catalogue or SMC website (URL http://www.smcworld.com) for more information about wiring. Value setting To input a value for pressure setting or other purposes: 1.