A_HEC-OM-J017 When the Upper temperature limit alarm and the DC power voltage alarm go off simultaneously, D2 will be 23X1+22X0+21X0+20X1=9(=39H). HEC 4-4 Details of Communication Format 4-6 Reading temperature average data Note) For this product, the average temperature data, Tm, indicates the temperature of the external sensor.
PID parameters are set incorrectly. setting Cause / Measure DC output voltage of product is reduced. Check the power voltage. Code Description Manner of reset ERR19 Abnormal auto tuning alarm Stop Overloaded during auto tuning mode Avoid overload. ERR02 System error 2 Stop The FRAM data was destroyed by highlevel noise.
Current limiting Power supply current Power supply voltage for pulse signal resistor R type limiting resistor 24V DC 10% 3.3k 5% (0.5W or more ) LEC-PA-R-332 5 VDC 5% 390 5% (0.1W or more ) LEC-PA-R-391 NPN type (LECPAN-) Power supply for pulse signal Inside of the driver Positioning unit side NP+ <3> 1k NP<4> 120 Current limiting resistor R PP+ <5> 1k PP<6> 120 Current limiting resistor
Connector 9 - (6) Power supply Supply power 24V DC. Caution Supply power first to the controller (LEC), then to the gateway unit. If power is supplied to the gateway unit and then to the controller (LEC), reset the data link after supplying power to the controller (LEC). (Refer to 12.4 Gateway unit control flag for the details of data link reset.)
Locking position 8 -
Maintenance Caution
The leakage current should be 5% or less (AC coil) or 2% or less (DC coil) of the rated voltage. 2. Use in low temperature environments Protection against freezing or solidification of impurities etc. When heating the valve body and piping by a heater, etc., be careful not to heat the coil with the heater. 4 Installation Warning 1.
Open the cover and set the address using an AS-Interface address programming device and DC power jack cable etc. (PEPPERL + FUCHS: VAZ-PK-V1-Cinch, SIEMENS: 3RK1901-3HA00 etc.) The Address assignment range is 1 to 31. The address can be set regardless of connecting order, but it is not possible to set address overlap. The address at shipment from the factory is 0.
Wiring Meaning Connector pin number Wiring colour 1 Brown Power supply DC(+) 2 White Analogue current output/Analogue voltage output 3 Blue Power supply DC(-) 4 Black IO-Link/Switch output (C/Q) Wiring specifications M8 Connector pin assignment M12 Connector pin assignment -11No.D-S-OMU0002-A Setting Initial settings are as follows: Switch output: Low (NPN = ON, PNP = OFF), Analogue output
Power supply (Valve) 24V DC -5% to +10% Current consumption Communication power supply 0.1A or less (24VDC) Enclosure IP20 Weight 80g or less CompoBus/S system specification Item Specification Applicable PLC OMRON Coop.
Therefore, when it is continuously energized or the energized period per day is longer than the de-energized period use a DC specification valve. For applications such as mounting a valve on a control panel, incorporate measure to limit the heat radiation so that it is within the operating temperature range.
DC output voltage of product is reduced. 1 Serial communications RS-232C / RS-485 RS-232C, RS-485 RS-232C ERR11 DC power supply failure Stop When no input is made within 1 minute regardless of setting mode, the A Power switch H Communication connector The fans at the power supply stops.
DC: less than 5% of rated voltage.
DC 24V power Power supply plug EMG supply C24V Wiring 24V 0V M24V 0V Electrical wire entry 4 - 1.2 Controller setting software version 1. Installation of software With the controller setting software CD-ROM, install the communication unit software, following the Software Installation procedure (PDF) 2.
If a control power supply is provided, DC specification has polarity. Follow the indication shown on the end of lead wire. 4. A wire for wiring should be 0.5 to 1.25mm2 or more as reference. 5. Give enough curvature to the lead wire not to have excessive force when it is fixed. 6. Fluid containing foreign matters and oil will cause malfunction and sealing failure.
Load voltage Auto switch model Lead wire length (m) Special function Indicator light Flexible (2) Pre-wire (1) Wiring (Output) Type Solid state switch Electrical entry Applicable load Electrical entry lead wire (-61) 0.5 (Nil) 3 (L) In-line 5 (Z) connector DC AC Perpendicular 3-wire (NPN) Y69A Y59A IC circuit 5 V 12 V Y7P Y7PV Grommet Relay, PLC 3-wire (PNP) Standard Yes 24 V Y69B Y59B 12
PLC: Programmable Logic Controller Lead wire length (m) Auto switch model Flexible lead wire (-61) Load voltage Special function Electrical entry Applicable load Pre-wire connector Indicator light Wiring (Output) Type Electrical entry 0.5 (Nil) 3 (L) 5 (Z) AC DC Perpendicular In-line 3-wire (NPN) M9NV M9N 5 V 12 V IC circuit Standard 3-wire (PNP) Solid state switch M9P M9PV M9B M9BV 2-wire
Please contact SMC if an inverter welder or a DC welder will be used. When a magnetic body surrounds the cylinder as shown in the figure below (including when the magnetic body is only on one side of the cylinder), the movement of the auto switch may become unstable, so please contact SMC. 12 to 16 32 to 63 Magnetic body (Iron plate, etc.)
Auto switch Lead wire* (m) Without auto switch (Built-in magnet) Load voltage Indicator Style Special function Wiring (Output) Electrical entry Auto switch model Applicable load 0.5 () 3 (L) 5 (Z) None (N) DC AC * Refer to the left table for selecting applicable auto switches. 3 wire (NPN) C76 C73 C80 B53 B54 B64 C73C C80C A33A A34A A44A B59W H7A1 H7A2 H7B H7C G39A K39A H7NW H7PW H7BW H7BA
The graphs are based on operation using an SMC DC power input type driver with halfstep energization.
Load voltage Auto switch model Lead wire length (m) Special function Indicator light Flexible (2) Pre-wire (1) Wiring (Output) Type Solid state switch Electrical entry Applicable load Electrical entry lead wire (-61) 0.5 (Nil) 3 (L) In-line 5 (Z) connector DC AC Perpendicular 3-wire (NPN) Y69A Y59A IC circuit 5 V 12 V Y7P Y7PV Grommet Relay, PLC 3-wire (PNP) Standard Yes 24 V Y69B Y59B 12