PFxx-OMX0007 switch output PNP/NPN) U8 1 Y 0: NPN 1: PNP Setting the switch output 1020 0x03FC 0 R/W 1030 0x0406 0 R/W Change by FUNC U8 0 Y 0: Aout (Analogue output) 1: in (Exterior input) FUNC terminal function setting 0: std (Standard condition) 1070 0x042E 0 R/W Reference condition U8 0 Y 1: nor (Normal condition) 0: HYS (Hysteresis) 1: Wind (Window comparator) oUt1 (Selection of output mode) 2: AC
[AC] When accumulated output is selected Press the button to move on to accumulated output setting. (Refer to page 37.) [OFF] Switch output OFF is selected. Press the button to move on to display colour setting. Flow setting Set the flow based on the setting method on page 26.
Rated Rated Sensitivity voltage x size voltage current of leak [V] [A] current [mA] HRS012--10 HRS018--10 1-phase 100V AC(50Hz) 100 200 15 15 or 30 HRS01--10-T 1-phase 3 cores x Sharing 100V to 115V 14AWG (High pump head AC(60Hz) [Optional]) (3 cores x 2.0mm2) HRS012--20 HRS018--20 HRS024--20 1-phase 10 30 (including ground) 200, 200-230V AC 230 HRS0--20-T (50/60Hz) 15 30 (High pump head
specification Item Specification Insulation system Photo coupler Rated input voltage DC24V Contact Run/Stop signal External switch signal input Used input voltage DC 21.6V to 26.4V signal1,2 Rated input current 5mA TYP Input signal 4.7k Rated load voltage AC48V or less /DC30V or less Signal of operating status Signal for the alarm status Signal for completion of preparation Contact AC
The AMS components are compatible with SMCs modular AC-D F.R.L. system and can be combined with existing installations. Two versions of the Air Management Hub are available, base type and remote type. These can be combined to create a wireless network of up to 11 Air Management Hubs (1 wireless base + 10 wireless remotes).
1500V600V 10G XYZ 3 AC AC1500V1 3mA DC12V AC500V1 3mA 1.0A AC DC500V 50M 690g 13
3-3 7.6 R03-R8M 205m 50cm 14.5mT DC10.826.4V1 50mAMAX. 0.1mm/ 02mm 1 MAX.DC30V50mA) A /B 500mm/s AC500V1 (12E ) DC500V50M (12E ) 33.3Hz6.8G XY 2 Z 4 JIS D1061 30G XYZ 3 IP65
230V(50Hz) FM MC PRS PRS2 ILS THR C01 C11 TB IDFA80/90 CN GFCI EDV PE BK WH GR SY BU BR AC 230V(50Hz) G/Y / IDFA60/70/80/90 Series 7-4 IDX-OM-W094 7.5 IDFA60/70/80/90 Series 7-5 IDX-OM-W094 A 8 A 8.1 8.2 A (10) 8.3 8.4 IDFA60-20-A IDFA70-20-A IDFA80-20-A IDFA90-20-A 10 m 3/min(ANR) 186 300 462 576 10 1) ANR 65% 2) IDFA60/70/80/90 Series 8-1 IDX-OM-W094 A 8.5
AC
When the rated voltage is AC and if it is assembled with the coil for DC, response may be delayed and occur malfunction. Also, for DC valves, when the coil for AC is assembled, it occurs malfunction. Pay attention that the coil is assembled correctly after performing maintenance for the coil.
DC coil 2% or less of the rated voltage AC coil 15% or less of the rated voltage 2. Solenoid valve drive for AC with a solid state output (SSR, TRIAC output, etc.) 1) Current leakage 8. Regarding vacuum switch valves and vacuum release valves If a non-vacuum valve is installed in the middle of a piping system that contains a vacuum, the vacuum condition will not be maintained.
Recommended SMC cable: EX500-AC-SP Communication failure of the EX500 local bus SI unit communication LED is OFF Check the wiring length of the local bus cable and check that the recommended cable is used. Check that there is no high voltage cable or equipment that generates noise around the local bus cable. Separate the local bus cable away from noise sources.
DC24V Contact output signal (Alarm) Max. load current AC/DC 500mA (resistance load) Rated load voltage Max. AC48V/ Max.
Solenoid valve drive for AC with solid state output (SSR, TRIAC output, etc.) 1. Operation manual Warning Caution Install the products and operate them only after reading the operation manual carefully and understanding its contents.
Solenoid valve drive for AC with solid state output (SSR, TRIAC output, etc.) 1) Current leakage When using a snubber circuit (C-R element) for surge protection of the output, a very small amount of electrical current will continue to flow even during the OFF state. This results in the valve not returning.
<AC> There is no S option, since a rectifier prevents surge voltage generation.
Light/Surge Voltage Suppressor (VEX1501, 1701, 1901) Caution AC DC Electrical Connection (VEX1501, 1701, 1901) DIN terminal is connected inside as in the figure below. Connect to the corresponding power supply.
Internal voltage drop Indicator light (lights when ON) Applications AC DC 24V or less AC DC 48V or less AC DC100V or less 24VDC 100VAC 50mA 40mA 20mA 5 to 40mA 5 to 20mA Relay, PLC, IC circuit D-A90 D-A90V None 0 Relay, PLC D-A93 D-A93V 2.6V or less D-A96 D-A96V 4 to 8VDC 20mA 0.8V or less IC circuit Lead wires D-A90, A93 : Oil resistant heavy duty vinyl cord 2.7 0.18mm x 2 wire (Brown
Electrical entry direction Perpendicular Perpendicular Perpendicular Wiring type 3-wire 2-wire IC circuit, Relay, PLC Applicable load IC circuit Relay, PLC AC DC 24V or less/50mA Load current range and Max. load current 24VDC/5 to 40mA 100VAC/5 to 20mA Load valtage AC DC AC DC 4 to 8VDC/20mA 48V or less/40mA 100V or less/20mA Contact protection circuit None 2.4V or less (to 20mA) 3V or less
Auto Switch Specifications Grommet Electrical entry:In-line PLC: Programable Logic Controller D-A90, D-A90V (without indicator light) D-A90, D-A90V Switch model Applicable load IC circuit, Relay, PLC Load voltage AC DC AC DC AC DC 24 V or less 48 V or less 100 V or less Maximum load current 50 mA 40 mA 20 mA Contact protection circuit None 1 or less (including lead wire length of 3 m) Internal