LJ1H

Note 2) To insert the T-nuts, remove the covers at both ends of the body and insert them into the T-slots.

SZ3000

When ordering TUV approved products, add " Q" at the end of the standard part number.

5 Port Solenoid Valve, Series VQC

rated voltage) None Operates at 1A Typ.

0.4

SOL.A 17 16 () (+) 21 25 24 Gray Red 23 Station 11 13 3 SOL.B () (+) 22 18 23 Black White 24 SOL.A 12 4 () (+) 23 26 Station 12 White None 25 19 22 SOL.B () (+) 24 11 5 21 20 White None 26 COM. 10 9 8 7 6 (+) () 25 COM. M27 female thread (+) () 26 Electrical characteristics Note) Positive COM spec. Negative COM spec.

Modular Type Lubricators Series AL

*Note: Bracket is not assembled and is supplied loose at time of shipment.

4 Port Direct Operated Poppet Solenoid Valve Series VQD1000 1

As a rule, a DIN rail must be secured at 5 station intervals as follows: 2 to 5 stations at two locations, 6 to 10 stations at three locations, 11 to 15 stations at four locations, 16 to 20 stations at 5 locations.

Solid State Auto Switches

at 24 VDC Leakage current 0.8 mA or less at 24 VDC Operating range .

CM2

If the cylinder is operating at a high frequency, be aware that the cylinder tube surface could become very hot, creating the risk of burns. If the cylinder is operating at a high frequency, be aware that the cylinder tube surface could become very hot, creating the risk of burns. eThe One-Touch fitting cannot be replaced.

Vacuum

Flat wlth rib 1 0 1 2 21 29.946 5 6 1 . 7 1 3 1 5 't2 21 29.946 5 6 3 1 . 8 '19 20 1 6 1 8 12.5 215t301 46.S 5 3.5 Dep type 23 23 22 23 23 22 50 48 50 Applicable Tube ) 56 54 56 54 57 co 57 '5l3e" lube may be subslituled for 4mm.

VQ5000

(Order separately) Note 2) Mount so that the exhaust cleaner is at the lower side.

SMC Basic Pneumatics

The movement starts at zero and reaches about double the average speed (Stroke per time) at the end of stroke.

%silltr

The movement starts at zero and reaches about double the average speed (Stroke per time) at the end of stroke.

Auto Switch Guide

D-J51: 5 ms or less Except D-J51 (1 mA or less at 100 VAC, 1.5 mA or less at 200 VAC), D-M5NW/M5PW/M5BW, D-F9BAL, D-P5DWL (1 mA or less at 24 VDC).

Rubber seal 5 Port Solenoid Valve Series SYJ5000

. 10 28.1 [35.1] 60.9 53.4 12.7 M8 x 1 32.6 42.1 15.1 39.2 [46.2] Approx. 300 (Lead wire length) Pg7 20 20 20 20 107 [111.4] 3 3 3 3 87.4 [91.8] 105.2 125.2 90.4 77.4 45.4 127 11 11 11 11 23 2-2.6 (For mounting) 2-2.6 (For mounting) 2-2.6 (For mounting) 23 23 23 27 2-2.6 (For mounting) Refer to the page 91 for dimentions with connector cable. 29 Series SYJ5000 3 Position Closed Center/Exhaust

VXR21/22/23

Return voltage is 20% or more of the rated value at AC power and 2% or more at the DC power. Allowable voltage fluctuation is 10% of the rated voltage.

XL

Load voltage at ON = x 2 pcs.

High Vacuum Angle Valve, XL Series

Load voltage at ON = x 2 pcs.

RHC

Lateral load Relief valve adjusting screw Relief valve adjusting screw 6 turns at most (20, 25, 32, 40, 50) 10 turns at most (63, 80, 100) 6 turns at most (20, 25, 32, 40, 50) 10 turns at most (63, 80, 100) 10-6-4 4 Series RHC Model Selection Model Selection Example of High Power Cylinder Selection Example: 1 Graph (1)-1 Horizontal Drive Supply Pressure 0.5 MPa RHC63 84J 10 RE A B Operating

Electric Actuator with Integrated Guide

The operation of the actuator should be confirmed at a low speed. Operate it at the prescribed speed only after proper operation is confirmed. 96 100 Series LTF Electric Actuator Precautions 2 Be sure to read before handling. Mounting Power Supply Caution Caution 1. Do not use until you verify that the equipment can operate properly. 2.

Digital Flow Switches

Be certain to turn on the power when the flow rate is at zero. Allow an interval of 10 minutes after turning on the power, as there are some changes in the display. 5. Flow rate unit Switch measures at mass flow rates without being influenced by temperature and pressure.