NCY2 series If the current exceeds the specification failure may occ!r. Applicable model: D-A73, A73H, A73C, E7 3 A.Z7 3t D -97.93 A.
It may not be possible to connect them, or they may cause other trouble, such as air leakage or the tube pulling out after connection. Back Pressure Check Valve Built-in Type D D S S Caution Wiring specifications symbol Valves with built-in back pressure check valve is to protect the back pressure inside a valve.
Thus, even if the mass is small, when "r" is large the resulting moment of inertia (I= mr) is large, and since the kinetic energy "E" also becomes large, this may lead to damage of the shaft, etc.
The supply pressure is relatively high (approx. 0.5 MPa or more), the set pressure is low (approx. 0.1 MPa or less), and when operated with the output side released to the atmosphere, there may be pulsations in the setting pressure.
If supply pressure to this product is interrupted while the power is still on, the internal solenoid valve will continue to operate and a humming noise may be generated. Since the life of the product may be shortened, shut off the power supply also when supply pressure is shut off. 5.
When the compressed air is used for air blow, the exhausted air from the blow nozzle may have taken in airborne foreign matter (such as solid particle, fluid particle) from the surround air. The foreign matter will be sprayed on the work, and the airborne foreign matter may adhere to it. Therefore, use caution for the surrounding environment.
Note that operation exceeding the rotation time adjustment range, may lead to sticking or stopping of operation.
The product specified here may become unsafe if handled incorrectly. The assembly, operation and maintenance of machines or equipment including our products must be performed by an operator who is appropriately trained and experienced. hexagon wrench for the bore sizes listed below.
AB B MK MK Basic (mm) MK2T A B C D E F Yh9 G 45 52 64 77 H 16 16 20 20 I 9 9 11 14 J 7 7 8 10.5 K M6 x 1.0 M6 x 1.0 M8 x 1.25 M10 x 1.5 L 10 10 14 18 S 31.5 29 34 34.5 T 10.5 9 11.5 10.5 W 14 15 19 19 X 3 3 3.5 3.5 Z 6.5 6.5 7.5 7.5 AA 4.5 5 7 7 AB 1 1 1 1.4 AC 5.5 5.5 6.6 9 AE 1/8 1/8 1/4 1/4 Model 30 30 37 48 MKB32-Z MKB40-Z MKB50-Z MKB63-Z 0 0.062 0 0.062 0 0.062 0 0.062 49.5 57 71 84
Series Bore size (mm) CP95 8 BJ2-008 C85 10 BJ2-010 12 BJ2-012 16 BJ2-016 20 BM2-020 25 BM2-025 NCM Maximum Piston Speed NCA If an auto switch is set at mid-stroke, the electrical device to which it is connected, may not operate if piston speed is too high.
*When using mounting brackets (foot, head side flange, or double clevis), an auto switch may or may not be mounted later. Confirm specifications. Mounting Bracket Part No.
MAY 2001 World Wide Support... Europe ENGLAND SMC Pneumatics (U.K.) Ltd.
www.stevenengineering.com I 3.1 FLOW CONTROL EQUIPMENT SPEED CONTROLLERS SPEED CONTROLLER WITH ONE-TOUCH FITTINGS: IN-LINE TYPE SERIES (N)AS1001-4001 Minimizes Installation Time and Cost Accepts Nylon and Polyurethane Tubing Wide Variety Of Sizes Speed may accurately be controlled even at low velocity Constant Speed easily set Retaining prevents accidental loss of needle H O W T O O R D E
Oprating Environment Handling Caution Warning rIf supply pressure to this product is interrupted while the power is still on, the internal solenoid valve will continue to operate and a humming noise may be generated.
Caution When using auto switches shown inside ( ), stroke end detection may not be possible depending on the One-touch fitting or speed controller model.
Applicable shaft types: S, W D20Depending on the change that has been made, the flat portion of the standard product may remain. E1 = Short shaft side Short shaft side X = Y L4 = L2 = X = C2 Y = C1 = C C2 = C E2 = D1 = E3 = D2 = Long shaft side Long shaft side C1 Y= Depending on the change that has been made, the flat portion of the standard product may remain.
Otherwise, faulty operation and dropping of durability may occur. w When fitting the guide body, use the guide body which has high flatness of the fitting surface.
Damage may occur due to excess current flow into a switch. 4.
This may not only cause broken lead wires, but it may cause internal elements of the switch to be damaged by the stress. 3. Mount switches using the proper tightening torque. When a switch is tightened beyond the range of tightening torque, the mounting screws, mounting bracket or switch may be damaged.
Otherwise personal injury and damage to equipment may result.