A-HEC-OM-J004 Do not use them for other purposes.
Inch size Millimeter size Port size 5/32 04 03 4 M5 M5 x 0.8 Thread type 1/4 06 07 6 U10/32 10-32UNF 5/16 08 09 8 Metric system thread (M5) 01 1/8 3/8 10 11 10 Nil Unified thread (10-32UNF) 02 1/4 1/2 12 13 12 Rc(PT) 03 3/8 N NPT 04 1/2 Check valve free flow direction Applicable Tube O.D.
Do not wire with power lines or high voltage lines. Wire separately from power lines or high voltage lines, avoiding parallel wiring or wiring in the same conduit with these lines. Control circuits, including switches, may malfunction due to noise from these other lines. 5. Do not allow short circuiting of loads.
When using other than SMC brand tube, confirm that the following specifications are satisfied with respect to the tube outside diameter tolerance. 1) Nylon tube within 0.1 mm 2) Soft nylon tube within 0.1 mm 3) Polyurethane tube within +0.15 mm Port plate Caution Tightening torque M2: 0.16 Nm (SY3000) M3: 0.8 Nm (SY5000/7000) 0.2 mm Do not use tube which do not meet these outside diameter
Do not drop or bump the product. Dropping or bumping while handling may cause damage to the product. 5. Lead wire dimensions Covering: 3.4 Insulator: 1.1 Conductor: 0.64 Pressure Supply Warning 1. Do not use the switch with corrosive gas or liquid. Operating Environment Do not use the switch with corrosive gas or liquid. Such gas or fluid may cause damage to the switch. Warning 2.
Do not drop or bump the product. Dropping or bumping while handling may cause damage to the product. 5. Lead wire dimensions Covering: 3.4 Insulator: 1.1 Conductor: 0.64 Pressure Supply Warning 1. Do not use the switch with corrosive gas or liquid. Operating Environment Do not use the switch with corrosive gas or liquid. Such gas or fluid may cause damage to the switch. Warning 2.
Do not allow air flow that exceeds the rated flow. If the air flow is allowed outside the range of the rated flow even momentarily, drainage and lubricant may splash at the outlet side or cause damage to the component. 2. Do not use in a low pressure application (such as a blower).
For AC2040 For AC3040 For AC4040 For AC4040-06 Model Description 02 03 04 06 E50-06 E3002 03 04 E2001 02 03 E40Piping adapter Attachment Accessory 4 4 4 06 4 VHS201 02 02 03 VHS3000VHS402 03 04 Y24-01 02 02 Y34-01 Y44-02 03 Y54-03 04 02 03 04 2 2 2 Y IS1000E02 03 04 3 3 3 Y IS1000EIS1000EY 01 02 03 Pressure switch with piping adapter Residual pressure exhaust 3 port valve Cross interface
Do not wipe out the grease in the sliding part of the air cylinder.
Do not apply torque at other points as the product may be damaged. Rotate body A manually for positioning after installation. 12. Do not use body A and/or elbow body for applications involving continuous rotation. Mounting Body A and the fitting section may be damaged. Warning 1.
X Port size) Silencer System Solenoid valve Speed controller VFS 4 X 1/8 AS2301F01-04 A VS SYJ5l40-01 Rc(PT)1/8 (S = 4.5mm2) AS2301F01-06 B VS7 AN110-01 (S = 35mm2) Plate fixing screw 6 X 1/8 AS3301F -06 02 03 C 8 X 1/8 AS3301F -08 02 03 D Note) Do not loosen plate fixing screw. 1.2-31 Series SYJ5000 How to Order Light and surge voltage suppressor For electrical entry G,H,L and M Configuration
Supply pressure: 0.3 to 1.0 MPa Set pressure: 0.2 MPa Flow rate: 0 L/min (ANR) IR3000-03 IR3000-03 IR3000-03 Supply pressure: 0.5 MPa Back pressure: 0.5 MPa 0.204 0.5 0.2 Set pressure P2 (MPa) Set pressure (MPa) Set pressure (MPa) Set pressure (MPa) 0.202 0.4 Set point 0.15 0.200 0.3 0.1 0.198 0.2 0.196 0.05 0.1 0.194 0 0.2 0.1 0.4 0.3 0.6 0.5 0.8 0.7 0.9 1.0 0 500 1000 1500 2000 2500 3000
Akihabara UDX 15F, 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021, JAPAN Phone: 03-5207-8249 Fax: 03-5298-5362 URL http://www.smcworld.com 2007 SMC Corporation All Rights Reserved Specifications are subject to change without prior notice and any obligation on the part of the manufacturer. 1st printing KY printing LX 13500DN Printed in Japan.
Description Replacement parts Tubing outside diameter Metric sizes Inch sizes Body class Type LQ-GP J 3 03 03 4 04 04 04 04 6 06 06 06 8 08 10 10 10 12 12 12 19 19 19 25 25 1/8" 03 03 03 03 3/16" 05 05 1/4" 07 07 07 3/8" 11 11 1/2" 13 13 3/4" 19 19 1" 25 Insert pin holder assembly (with the parts case) Type Insert pin/ Holder type 1 2 1 2 3 4 5 6 J Insert pin material (J/K type
Range Setting Enabled Section 2 Maker setting Do not change.
Do not unpack the device until installing it. Do not drop or knock the controller. Keep the flow ports and cable glands plugged until installing.
Ltd. 1-16-4 Shimbashi, Minato-ku, Tokyo 105-0004, JAPAN Tel: 03-3502-2740 Fax: 03-3508-2480 URL http://www.smcworld.com 2000 SMC CORPORATION All Rights Reserved Specifications are subject to change without prior notice and any obligation on the part of the manufacturer. Printed in Japan. 1st printing December, 2000 D-SMC.L.A. P-80 (N)
Do not use in an atmosphere where corrosive gases, chemicals, sea water, water, or water vapor is present. Do not use in cases where there is direct contact with any of the above. 2. Do not use in an explosive environment. 3. Do not use in a place subject to heavy vibration and/or impact. 4. The valve should not be exposed to prolonged sunlight. Use a protective cover if necessary. 5.
Do not use in an atmosphere where corrosive gases, chemicals, sea water, water, or water vapor is present. Do not use in cases where there is direct contact with any of the above. 2. Do not use in an explosive environment. 3. Do not use in a place subject to heavy vibration and/or impact. 4. The valve should not be exposed to prolonged sunlight. Use a protective cover if necessary. 5.
;'16" 03/4" 'ol/2~ AsP330F'!U R(PT)1/8 M5 X 0.8 J\SP. 4;JOF~02 R(PT)I /4 Rc(PD1 /8 IIS'P530F:03 R(PT)318 Rc(PT)lIS 'ASi"!)30l"'lJ4 " R(PT)1!2 Rc(PT)1I4 ASP;l3OF:,FO~ RIPT)114 G(PF)1I8 I\Sps:ioFf;03' R(PT)318 G(PF)118 ),I'SPsJOF;;04: R(PT)1 /2 G{PF)1/4 A~P33!1F" 'l Il1 NPT1 /8 10-32UNF ,~Sp430FNO,?