Digital Flow Monitor No.10 There are differences Refer to Trouble in the displayed values when using more than one No.11 pressure switch. The display accuracy Refer to Trouble does not meet the No.12 specifications. Applied voltage does Refer to Trouble not match with the No.8 displayed flow value. The Display Refer to Trouble measurement unit No.13 cannot be changed. Buttons do not work.
No.PF-OMG0010-H PRODUCT NAME Digital Flow Switch (Integrated display type) MODEL / Series / Product Number PF2A7##H Table of Contents Safety Instructions 2 Model Indication and How to Order 10 Summary of Product parts 11 Definition and terminology 12 Mounting and Installation 14 Installation 14 Piping 15 Wiring 16 Outline of setting 18 List of outputs 19 Function selection mode 20 F_0 Initialize
Rc(NPT)11/4 40 to 42 Nm Hysteresis H_1 Item Default setting / With the temperature sensor in parenthesis (Displayed alternately) Flow [L/min] Rc(NPT)11/2 48 to 50 Nm [F 3] Response time setting 1 second Temperature upper limit exceeded If the tightening torque is exceeded, the product can be broken. If the correct tightening torque is not applied, the fittings may become loose.
Piping port (IN side) 11/4 54 mm Measurement mode Bracket (Option) 11/2 54 mm *: Green: Flashes once. PF3W5 -1 (Analogue 1 to 5 V type: Without temperature sensor) Flashes twice. PF3W5 -2 (Analogue 4 to 20 mA type: Without temperature sensor) Flashes three times. PF3W5 -1T (Analogue 1 to 5 V type: With temperature sensor) Tighten to the specified torque for piping.
Otherwise it can cause failure or malfunction of the system. 11/4 54 mm Temperature upper limit exceeded Flow range, unit specification and mounting of temperature sensor are displayed Set value Sets the ON or OFF point of the switch output. 50 oC 11/2 54 mm The fluid temperature is above 110 oC. Reduce the fluid temperature.
Do not continue idling except for priming the pump. 5 11. Condensation and freezing of the pilot port The location around the switching valve and the air exhaust port can cool down quickly due to expansion of the supply air, and this may cause condensation on the piping and the condensation may freeze during operation in winter.
Do not continue idling except for priming the pump. 5 11. Condensation and freezing of the pilot port The air supply port of the air operated type can cool down quickly due to expansion of the supply air, and this may cause condensation on the piping and the condensation may freeze during operation in winter.
Troubleshooting P.11 to 12 9. Construction and operating principle -P.13 10. Operating principle P.13 11. Sensor mounting (leakage sensor) P.14 1 Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of Caution, Warning or Danger.
Looseness of bolts which fix the parts at each port (port, elbow fixing flange, port fixing flange, air port cover). 11 9.
Dimensions --11 7. Guaranteed term and guaranteed range 12 8. Parts replacement procedure 13 1 XL-OMP0001 Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of Caution, Warning or Danger.
External gripping 11 34 42 65 158 254 force D I.D. Internal 17 45 66 104 193 318 Note 1) Gripping force per finger Effective value (N) gripping force O.D. External gripping S 7.1 27 33 45 131 217 force I.D.
General requirements) ISO 10218-1992: Manipulating industrial robots -Safety JIS B 8370: JIS B 8361: JIS B 9960-1: 1 ) JIS B 8433-1993: *2) 1. 2. 3. 1. 2. 3. 4. 2 - / *3) 1 1.5 *3)1 1 () 3 - 1 1-1. 1)0.5MPa L = 20mm MHZ2-10* MHZ2-16* MHZ2-20* MHZ2-25* MHZ2-32* MHZ2-40* mm 10 16 20 25 32 40 D 0.20.7 0.10.7 MPa S 0.350.7 0.250.7 C oC -1060 mm 0.01 0.02 c.p.m. 180 60 D 11
Gripping point . 11 3-5. Dimensions . 12 3-5-1. JMHZ2-16D-X7400B-DTP-(N/P) . 12 3-5-2. JMHZ2-16D-X7400B-HC10DT-(N/P) . 13 3-5-3. JMHZ2-16D-X7400B-HC10-(N/P) . 14 3-6. Connector and pin layout . 15 3-6-1. JMHZ2-16D-X7400B-DTP-(N/P) . 15 3-6-2. JMHZ2-16D-X7400B-(HC10DT/HC10)-(N/P) . 16 3-7. Center of gravity . 17 4Product Specifications . 18 4-1.
Operation failure Incorrect wiring (1) Fuse blown out and/or lead wire broken (2) Incorrect contact at the contact and connection (3) Broken wire in the coil (4) Foreign matter caught in the spool valve (8) Swollen spool valve (5) Excessive oil supply (11) Coil has burned out.
Wire the communication line away from the noise source. 11 NS: Green LED is flashing Communication is not established. Check the following, and restart. Signal line is connected from PLC. The communication speed of PLC and SI unit is appropriate. Wire the communication line away from the noise source. NS: Red LED is flashing Communication timeout.
Fault No.11 Problem Possible cause Investigation method Countermeasures The inputs that are beyond the maximum point number do not operate. Check that the number of inputs has not exceeded the allowable number. The allowable number depends on the SI unit model. Inadequate total number of inputs from the Input block connected with the SI unit.
Description and Functions 9 5-1 LED indication 9 5-2 Terminal board 9 5-3 Address setting 10 5-4 Setting of Hold/Clear 11 6. Wiring 12 6-1 Communication wiring 12 6-2 Terminal resistance 13 6-3 Cable for communication line 13 6-4 Wiring to power supply 13 7. Troubleshooting 14 -1No.EX-OMF0012-B 1.
If the minimum setting unit is 1 L/min, the flow can be displayed in 1 L/min units, i.e. 10, 11, 12. Minimum setting unit N Normal condition (NOR) Reference condition for volumetric flow: 101.3 kPa, 0 C The flow measurement which is converted at normal atmospheric pressure conditions at 0 C.
No.PS-OMM0005-J PRODUCT NAME Digital Pressure Switch MODEL / Series / Product Number ZSE10(F) ISE10 Table of Contents Safety Instructions 2 Model Indication and How to order 9 Summary of Product parts 11 Definition and terminology 12 Mounting and Installation 15 Installation 15 Piping 17 Wiring 18 Internal circuit and wiring example 19 Pressure Setting 20 Measurement mode 20 Function Setting
Recommended tightening torque: Modular AR/AW series 0.60.05 Nm ARM10/11 series 0.320.03 Nm Mount the main body of the Pressure switch. Insert the lock pin to the adapter to the end firmly. Supply pressure slowly, and ensure no air leaks.