AC Servo Motor Driver (CC-Link Type) Reset (RES) Keeping RY(n 1)A or RY(n 3)A (RES) ON for 50ms or longer RY(n 1)A RY(n 3)A 1 allows an alarm to be deactivated. Some alarms cannot be deactivated by Reset RY(n 1)A or RY(n 3)A (RES). (Refer to section 10.4.1.) If RY(n 1)A or RY(n 3)A (RES) is turned ON with no alarm occurring, the base circuit will not be shut off.
This produces an air cushion cylinder which retains the merits of a compact design. Operating principle A + A' A' qWhen the piston is retracting, exhaust is discharged from both A and A' until piston seal H passes the air passage A. wAfter piston seal H has passed the air passage A, exhaust is discharged only from A'.
This is equivalent to a magnetic field of approximately 18 cm in radius from a welding area using a welding amperage of almost 15,000 amperes. To use the system in a magnetic field that exceeds this value, use a magnetic material to shield the sensor unit.
This is equivalent to a magnetic field of approximately 18 cm in radius from a welding area using a welding amperage of almost 15,000 amperes. To use the system in a magnetic field that exceeds this value, use a magnetic material to shield the sensor unit.
SOL. location A B A B A B A B () A B () () 0 1 2 3 4 5 6 Double Double Single SI unit A side B side 3 position A B A B B A B A B A VQC Double Double Single SI unit A side B side 3 position Stations 1 2 3 4 5 SQ The places of asterisk are not used. 3 position uses two stations for wiring.
In order to measure with a discrimination of 0.01 mm, a counter with a 4 times multiplication function (CEU5) is required.
ao . , , , , t o o 3 . , , . , 05 stePping a ''.a: ' , . a , : a : l r : : i : l ::: I iob' ' ', ' t99;:9i1':i1:t t: llli,2.gtepping O8: 12mm lead , , . , , 1 ( } . u 5 asbinriea,i : r iri llliqq'i'' o5 stepoinq 30 08; zmm lead o2 stepping 80 08; 5mm lead 10.03 30 08; 2mm lead s5 stepping 80 08; 5mm lead a I a a a 100 O8; 6mm lead o2 stepping 200 08; 12mm lead 10.05 I M <-iD;;,;; uo100 08
In an environment where the product will come into direct contact with rain, wind and snow or with a lot of moisture (relative humidity 85% or more). (Note) In a location with a large quantity of dust. In a location containing flammable or explosive gases. In a location exposed to corrosive or flammable gases or solvent.
(RES) A.10 Undervoltage A.12 Memory error 1 (RAM) A.13 Clock error A.15 Memory error 2 (EEP-ROM) A.16 Encoder initial communication error1 A.17 Board error A.19 Memory error 3 (Flash-ROM) A.1A Motor combination error A.1C Software combination error A.1E Encoder initial communication error 2 A.1F Encoder initial communication error 3 A.20 Encoder normal communication error 1 A.21 Encoder normal
Use caution to the popping of a snap ring. When replacing rod seals and removing and mounting a snap ring, use a proper tool (snap ring plier: tool for installing a type C snap ring). Even if a proper tool is used, it is likely to inflict damage to a human body or peripheral equipment, as a snap ring may be flown out of the tip of a plier.
For the angle adjusting type, angle adjusting screws are mounted to the left cover. k e of y e gr g Angle adjusting screw o n o Angle adjusting screw ra v e n io 1 8 at 0 ot R n io ct re di g n ti us n A dj io n a gl ct e re e gl a di dj n g u in A st st in u g dj 0 di 0 a re 8 8 e ct gl 1 1 io n R n A e R e o v v o t o o a t o a o ti o r ti r g g n o n y y r a e e r n k a k g f o e n f
A ARP w y IR-A IR r IRV i VEX SRH !
The AL-D series of modular lubricators brings a modern appearance to SMC's line of lubricators while maintaining the high performance of our other series. The lubrication rate is easily adjustable without tools to meet equipment needs. The transparent bowl guard on the size 30 and larger provides improved environmental protection as well as full view of the bowl contents.
The AL-D series of modular lubricators brings a modern appearance to SMC's line of lubricators while maintaining the high performance of our other series. The lubrication rate is easily adjustable without tools to meet equipment needs. The transparent bowl guard on the size 30 and larger provides improved environmental protection as well as full view of the bowl contents.
14 A Current consumption 5 A (100 V) to 2.5 A (240 V) 9 A (100 V) to 4 A (240 V) 10 A (100 V) to 4 A (240 V) 8 A (200 V) Power consumption 440 W*1 850 W*1 900 W*2 1500 W*2 Alarm Refer to Alarm.
For the angle adjusting type, angle adjusting screws are mounted to the left cover. k e of y e gr g Angle adjusting screw o n o Angle adjusting screw ra v e n io 1 8 at 0 ot R n io ct re di g n ti us n A dj io n a gl ct e re e gl a di dj n g u in A st st in u g dj 0 di 0 a re 8 8 e ct gl 1 1 io n R n A e R e o v v o t o o a t o a o ti o r ti r g g n o n y y r a e e r n k a k g f o e n f
O-ring Body Seal Stud Can be used for a wide range of pressures from a low vacuum up to a pressure of 1 MPa. Effective when piping in a confined space. Body part rotates allowing for positioning. The use of a special profile ensures sealing and reduces resistance when the tube is inserted.
Hs A B A B 32 to 100 D-A73C D-A80C D-J79C D-A79W D-F7WV D-F7V Approx.
Description B VNH1 VNH2 VNH3 VNH4 VNH1-16 VNH2-16 VNH3-16 VNH4-16 Bracket (with bolt and washer) 4.2-30 VNH Specifications 3 port valve 2 port valve A B A B VNH311 20A A B VNH411 25A A B VNH113 10A A B VNH213 15A A B VNH313 20A A B VNH413 25A A B VNH133 10A A B VNH233 15A A B VNH333 20A A B VNH433 25A A B VNH111 10A VNH211 15A Model Operating fluid pressure Fluid Operation 0 to 7.0MPa 0 to