Fieldbus System SPR3: Max. 1.0 A SPR2: Max. 2.0 A SPR4: Max. 1.0 A SPR5: Max. 2.0 A SPR7: Max. 1.0 A SPR6: Max. 2.0 A SPR8: Max. 1.0 A SDN1: Max. 2.0 A SDN3: Max. 1.0 A SDN2: Max. 2.0 A SDN4: Max. 1.0 A SMJ1: Max. 2.0 A SMJ3: Max. 1.0 A SMJ2: Max. 2.0 A SMJ4: Max. 1.0 A Supplied current IP67 IP40 IP67 14 to 122F (10 to 50C) 35 to 85%RH (No condensation) 500 VAC for 1 minute between terminals and housing
valve (A) (A) 4 (B) 2 (A) 4 (B) 2 Note) A 1 5 (R1) 3 (R2) 1 (P) 3 (R2) 5 (R1) 1 (P) N.C.
A void A void A void A void A void A B A B A B A B A B A A A B A B A B A A A A 6 7 8 9 10 11 12 13 14 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 15 0 0 1 2 3 4 5 SC type OMRON SYSBUS wire system compatible SD type Sharp Satellite I/O link system compatible Terminal block (LED) nomenclature ADDRESS NO. STATION NO.
Operate the piston within a range such that collision damage will not occur at the end of the stroke. When a cylinder is used in a clamping mechanism, there is a danger of work pieces dropping if there is a decrease in clamping force due to a drop in circuit pressure caused by a power outage, etc.
as a stopper, select a model with a stroke of 50mm or less.
P P For the release valve, select a 2/3 port valve with a low vacuum specification. Also, use a needle valve to regulate the release flow rate. During the adsorption and transfer of a workpiece, verification of the vacuum switch is recommended. In addition, visually verify the vacuum gauge when handling a heavy or a hazardous item.
P P For the release valve, select a 2/3 port valve with a low vacuum specification. Also, use a needle valve to regulate the release flow rate. During the adsorption and transfer of a workpiece, verification of the vacuum switch is recommended. In addition, visually verify the vacuum gauge when handling a heavy or a hazardous item.
P P For the release valve, select a 2/3 port valve with a low vacuum specification. Also, use a needle valve to regulate the release flow rate. During the adsorption and transfer of a workpiece, verification of the vacuum switch is recommended. In addition, visually verify the vacuum gauge when handling a heavy or a hazardous item.
Note 4) Since this is a special product, a manifold part number is not specified.
4 A 4 A 4 A 4 A 4 A 4 A 4 A 4 A 4 A 4 A 4 2-One-touch fitting (X, PE ports) Applicable tube O.D.: 6 2n-One-touch fitting (A, B ports) Applicable tube O.D.: 4 6 (L4) L3 (3.2) 113.7 U Side D Side 3.1 8 36.3 43.7 5.5 (DIN rail dimension) 35 18 28.8 DIN rail holding screw Manual override In case of locking type, turn after pushing in.
It cannot be mounted at a later time or used as a separate unit.
A O OUT 2 I N 1 SMC A J A IN OUT H G M Parts list Material Note Description No.
Do not use a load that generates surge voltage.
A Dimensions except A, L and L1 are the same as rod side flange style.
It is an assembly of a piston and a gasket (KSYP-13).
lrlA |.25N/A r{/A.1 3 .35 t ( l{/A 13.9 or.
Proper auto switch mounting positions (Series CE1) (mm) Bore size (mm) Auto switch model Symbol 20 32 40 50 63 12 A B A B A B A B A B A B A B A B A B 40.5 47 55 79 82 85.5 D-A7, A8 4 13 17 39 44 41.5 Contact protection box internal circuits 41 47.5 55.5 79.5 82.5 86 D-A7H, A80H, A73C, A80C, D-F7, J79, F7V, J79C 4.5 13.5 17.5 39.5 44.5 42 Choke coil OUT Brown [Red] CD-P11 38 44.5 52.5 76.5
Operating principle A + A' A' A Piston seal A' A' R H R H When the piston is retracting, air is exhausted through both A and A' until piston seal H passes air passage A. After piston seal H has passed air passage A, air is exhausted only through A'. The section marked with slanted lines becomes a cushion chamber, and an air cushion effect is achieved.
Recommended pneumatic circuit for the CKQG/P series The following is an example of a basic meter-out control circuit for operating a cylinder using an air filter, a regulator, a solenoid valve and a speed controller. 7) It is possible to use the pneumatic circuit shown below. However, unlock the cylinder before operating.
Refrigerant R134a (HFC) IDU E Drainage is discharged by controlling a solenoid valve with a timer. A strainer for solenoid valve protection and a stop valve are also included. (The external dimensions are the same as the standard product.)