HRX-OM-X037 ) M5 30 3-phase 4 cores x 460 to 480V AWG8 AC(60Hz) (4 cores x 8 mm2) HRL300-A-40 R8-5 40 including ground 1 Cable specifications are the examples when using the product at a continuous allowable operating temperature of 70 oC, with an operating voltage of 600 V and two kinds of plastic insulated wires at an ambient temperature of 30 oC.
Cooling fan Power supply connector (AC) Connector for the single phase AC (AC200 to 220V) power supply. A power supply cable is connected here. External sensor connector (EXT.SENSOR) To use learning control function, external sensor is connected. Connector for the upper/lower temperature limit alarm and output cut-off alarm. A relay contact is open or close when these alarms are output.
Configuration Minimum equipment and wiring requirements to get started 1 7 Provided by customer 100V AC /200 V AC Provided by customer 24 VDC Provided by customer 8 2 PC 6 4 Electric Actuators Ex) LEF Provided by customer 3 1 Driver LECSA*-S* 2 Motor cable LE-CSM-*** 3 Encoder cable LE-CSE-*** 4 I/O connector LE-CSNA I/O cable LEC-CSNA-1 5 USB cable LEC-MR-J3USB 6 Setup software (MR Configurator2TM
Table 21 Reed auto switch Mounting method to Auto switch model Voltage, current Application Indicator light Electrical entry the cylinder AC 24 VDC or less, IC circuit Max.50ma D-A9[](V) 0.10 Relay AC 48 VDC or less, Tie-rod No Grommet to 0.20 Nm Sequence controller Max.40ma mounting AC 100 VDC or less, Max.20mA 30 - Table 22 Reed auto switch Mounting method to Auto switch model Voltage,
Resistance DC500V with Above 50M, between Case & AC Line Mass 690g 14 3-3 Sensor Specifications 7, 6 Core Twisted Pair Shielded Wire Cable (Oil, heat and flame resistance cable) (Connector : R03-R8M, Tajima Musen Denki Company) Max.
1.0A Insulation Resistance Above 50M, between Case & AC Line Mass 690g 22 5-3 Sensor Specifications Connector Connector : R04-R8M, Tajimi Musen Denki Company Max.
=0.841 OK ML2B32 P19 21 5-1 () 25 32 40 0.10.8MPa 0.30.5MPa 1.2MPa 0.75MP 1001500mms( 100500mms) 560 mm 0+1.8 JIS B0209 Rc1/8 Rc1/4 5 6 8 5-2 CEU2 CEU2P (DIN ) PRESET PROGRAM RUN LCD() 116132 P.T.P point to point 1 9.9 0.1mm RAM 8K 5mm 4 2 END NPN DC30V50mA PNP DC30V50mA AC100V1550Hz/60Hz DC24V100.4A 050 2585 10~55Hz0.75mm XYZ 2 1s 1500V600V 10G XYZ 3 AC
Load voltage Internal voltage drop (illuminated load current load when ON) range AC DC 24V or less 50mA Relay D-A90 AC DC 48V or less 40mA Not provided PLC D-A90V IC circuit AC DC 100V or less 20mA D-A93 2.4V or less (up to 20mA) 3V or less DC24V 5 to 40mA D-A93 Provided Relay (up to 40mA) D-A93V PLC D-A93V 2.7V or less AC100V 5 to 20mA 2.7V or less D-A96 D-A96V DC4 to 8V 20mA 0.8V or less
DC coil 3% or less of rated voltage AC coil 15% or less of rated voltage (2) Solenoid valve drive for AC with a solid state (8) Regarding vacuum switch valves and vacuum output (SSR, TRIAC output, etc.) release valves 1) Current leakage When using a snubber circuit (C-R element) for surge protection of the output, a very small amount of electrical current will continue to flow even during
Solenoid valve drive for AC with a solid state output (SSR, TRIAC output, etc.) 1) Current leakage When using a snubber circuit (C-R element) for surge protection of the output, a very small amount of electrical current will continue to flow even during the OFF state. This results in the valve not returning.
. -29No.EX-OMP0005-I Cable with both sides connector (SPEEDCON) Part number: EX9-AC 005 MJ SSPS (Socket/Plug) Cable length (L) Connecter specification 005 500 mm SSPS Socket side: Straight, Plug side: Straight 010 1000 mm 020 2000 mm SAPA Socket side: Angled, Plug side: Angled 030 3000 mm 050 5000 mm 100 10 mm Straight connector type (EX9-AC#MJ-SSPS) Angled connector type (EX9-AC#MJ-SAPA)
DC coil 3% or less of the rated voltage AC coil 8% or less of the rated voltage 2. Actuator drive When an actuator, such as a cylinder, is to be driven using a valve, take appropriate measures (cover installation or approach prohibition) to prevent potential danger caused by actuator operation. 3. Effect of back pressure when using a manifold.
line: 1500 VAC, 1 minute Between case and signal earth: 500 VAC, 1 minute Insulation resistance Between case and AC line: 500 VDC, 50Mor more Ambient temperature 0 to + 50 (No freezing) Ambient humidity 35% to 85%RH (no dew condensation) Noise resistance Square wave noise by noise simulator (pulse width: 1s) Between power terminals: 2000V, input line: 600V Vibration proof Durable to 10 Hz
Solenoid valve drive for AC with a solid state output (SSR, TRIAC output, etc.) 1. Operation manual Install the products and operate them only after reading the operation manual carefully and understanding its contents. Also, keep the manual where it can be referred to as necessary. 2. Ensure sufficient space for maintenance activities.
T ground) HRSE012-A-20/23 1-phase 200V AC Lead wire end not Shared HRSE012-A-20/23-T (50/60Hz) 3 cores x 2.5mm2 treated with 100 V, 200 V HRSE018-A-20/23 (Bare cut) 15A 15A 30mA -23 Only (including HRSE018-A-20/23-T (L: Brown, N: Blue, PE:Green/Yellow) and 1-phase ground) HRSE024-A-20/23 230V 230V AC HRSE024-A-20/23-T (50/60Hz) HRSE Series 3.3 Installation 3-7 HRX-OM-R039 Chapter 3 Transport
Port Size -Rc1/4 Power supply connector (AC) Connector for the single phase AC (AC100 to 240V) power supply. A power supply cable is connected here. External sensor connector (EXT.SENSOR) To use learning control function, an external sensor must be connected. Alarm output connector (ALARM) Connector for the upper/lower temperature limit alarm and output cut-off alarm.
Light/Surge Voltage Suppressor How to Change Passage State Caution M4X0.7 AC, 100 VDC or more In the case of indicator light assembly Terminal no. 1 (+) N.C. N.O. External pilot When change the passage state, confirm that pressure has Varistor been removed from the valve.
Connector for DIN Terminal VNA1 to 4 (Valve size 1 to 4) VNA5 to 7 (Valve size 5 to 7) Caution AC Terminal no.1 Coil Terminal no.2 DC Indicator light assembly Terminal no.1 (+,-) Coil Terminal no.2 (-,+) AC Indicator light assembly Terminal no.1 Coil Terminal no.2 DC pol Indicator light assembly Terminal no.1 (+) Coil Terminal no.2 (-) Electrical Connection Caution The DIN connector terminal
(except when the bowl material is metal) 225 Air Combination Series AC/ACG Air Filter + Regulator + Lubricator AC10 to 60 Options/Attachments Part No. Options/Attachments Part No.
Magnetic Field Resistant Auto Switches Type Auto switch model Applicable magnetic field Electrical entry Indicator light Wiring (Pin no. in use) Load voltage Lead wire length Applicable load P3DWASC AC magnetic field (Single-phase AC welding magnetic field) 2-wire (34) Pre-wired connector 2-color 0.3 m Relay, PLC P3DWASE 2-wire (14) P3DWA Grommet 2-wire 0.5 m P3DWAL 3 m P3DWAZ 5 m Solid state