HEC-OM-U015 Ambient environment use shielded 9 8 7 6 HECR012-W 4 Unused Unused cable connected When turning on/off the power observe the procedure. Otherwise 5 SG SG to this connector. D-sub 9 pin (socket type) Temp :-40 to 70 C (No dew condensation and icing) Humidity : 5 to 95%RH Environment : No corrosive gas, solvent such as thinner and flammable gas unexpected malfunction or danger may occur.
SUS+NBR 1 3 Piston Stainless steel 1 2 Head cover Brass 1 Electroless nickel plated 1 Body Aluminum alloy 1 Hard anodized No Description Material Qty Note 29 6 7 3 6 1 With auto switch 10 8 4 11 9 2 5 12 13 13 Magnet holder Brass 1 12 Magnet Magnetic material 1 11 Gasket NBR 1 10 Rod seal NBR 1 9 Piston seal NBR 1 8 Bumper Urethane 2 7 Rod end nut Steel 2 Nickel plated 6 Mounting nut Brass
to 16 stations SY3000-43-2ASY3000-43-3AType D, 9 to 16 stations Type u, 2 to 8 stations 7 Connector assembly SY3000-43-1NASY3000-43-2NAType D, 2 to 8 stations Type u, 9 to 16 stations SY3000-43-2NASY3000-43-3NAType D, 9 to 16 stations Type u, 2 to 8 stations 8 Dust cup VZ3000-63-2 9 Round head combination screw SY3000-23-4 M326 Matt nickel plated 10 Gasket SX3000-57-4 SX5000-57-6 11 DIN rail
Heavy load Standard load Medium load Light load 1 10 50 100 200 1 0.25 0.49 0.98 1.96 2 20 2 0.49 75 200 400 0.74 1.47 2.94 3 30 3 0.74 100 300 600 0.98 1.96 3.92 4 40 125 400 800 4 0.98 1.23 2.45 4.90 5 50 5 1.23 150 500 1000 1.47 2.94 5.88 6 75 200 600 1200 6 1.47 1.96 3.92 7.84 7 100 250 700 1400 7 1.72 2.45 4.90 9.80 8 300 300 800 1600 8 1.96 2.94 5.88 11.76 9 500 500 900 1800 9 2.21
TROUBLESHOOTING 9 7. CONSTRUCTION / PARTS LIST 10-11 8. SPECIFICATIONS OF BOWL ASSEMBLY 12-17 9. REPLACEMENT PROCEDURE 18-21 10. DISASSEMBLY DRAWING 22-25 11. DIMENSIONS 26 Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage.
TROUBLESHOOTING 9 6. CONSTRUCTION / PARTS LIST 1011 7. BOWL ASSEMBLY SPECIFICATIONS 1219 8. REPLACEMENT PROCEDURE 2023 9. DISASSEMBLY DRAWING 2428 10. DIMENSIONS 29 S FILTER REGULATOR Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage.
D-sub 9 pin (socket type) Fixed screw: M2.6 6-8 Unused Unused 9 Unused BUS 1-2 Unused 8 1 Install the product above 0.6m from the floor. 3-5 PT-RTD 5.2 Environment 6 Output Cutoff Alarm a contact (OPEN During Alarm) 15 9 Signal D-sub 15 pin (Socket type) 7 Output Cutoff Alarm Common External Do not use in an environment where the product is directly exposed to Fixed screw: M2.6 temperature
(Fig. 9) When the groove is used, do not deform the switch rail. 3-3-5) Switch response at intermediate positions of the stroke. Lead wire It is possible to install an auto switch at an intermediate Switch rail position of the stroke, but the maximum speed of the cylinder, which can be detected by the switch, will be limited due to the load relay response. Fig. 9 Switch rail 12/28 4.
When energizing to the coil assembly is stopped, valve (9) closes. Time s 0.150.2 s Ex.) For DC24. DC6 V specification, The time to apply starting voltage is same for all voltage. 4-2 XLS-**-P*G (with control power supply) Valve (9) opens when the coil assembly is applied the rated voltage. Valve (9) closes when the coil assembly is stopped being energized.
SeriesNCQ8 Air Cylinder: Standard Type Double Acting, Single Rod Maintenance Parts 056 to 400 Construction Double Acting, Single Rod 10 11 9 Seal Kit Parts List No. 9 10 11 Description Piston Seal Rod Seal Tube Gasket Material NBR NBR NBR *BLUE links will lead to purchase pages. Repair Parts: Standard Seal Kit for Double Acting, Single Rod Remarks Bore size Kit no.
Instruction Drawing for Disassembly & Reassembly of Filter u AIR VENT y i q 9-1 r 9-3 t 9-2 e w Stopper IN !2 !0 !1 DRAIN Element support Partition plate Filter case A OUT BACK WASH A A-A SECTION qHexagon head bolt wHexagon nut eWasher rCover tGasket yAdjustment bolt uLock nut iElement retainer oElement mounting bracket Spring 9-1 Vibration stop Element holder !0Element !1Joint !
9 !0 !7 !3 !5 u y q e w @2 !1 Open condition MHZ MHF MHL MHR MHK MHS MHC Component Parts MHT No.
Applicable bore A B A B A B MY-S25 MY-S32 MY-S40 ML1C25 ML1C32 ML1C40 103 117 35 50 8 5 9.5 5.5 M6 x 1 128 146 45 64 11.7 6 11 6.6 M8 x 1.25 148 170 55 80 14.8 5 14 9 M10 x 1.5 1114 A Hy-rodless Cylinder ML1C Series Construction #9 %7 #8 #7 %6 !0 CLJ2 CLM2 CLG1 CL1 w $8 @4 i u !7 t !2 $9 !3 !1 %5 @6 @5 $5 #6 MLGC %2 CNG @8 !9 MNB e CNA2 $2 q %3 %4 $1 CNS #1 #0 @9 #4 $0 !5 !
Soft nylon Polyurethane 4 3.2 KAU23-00 33 34 37 17.5 18 20 9.6 10.4 12.8 9 9.7 11.7 18.5 21 22 15.5 16 17 15.2 18.5 20.9 9.6 10.4 12.8 45.4 45.4 28.4 28.4 17.7 17.7 9 7 5 KAU04-00 KAU06-00 13.4 13.4 4.2 4.2 3.4 2.9 8 6 24.5 27.5 30 15.2 18.5 20.9 13.7 16.1 18.1 42.5 48 51 KAU08-00 11 16 12 10 KAU10-00 KAU12-00 23 Plug-in reducer: KAR Effective area (mm2) Weight (g) Tube O.D.
Design so that human injury and/or damage to machinery and equipment will not be caused when machinery is stopped by a safety device under abnormal conditions, such as a power outage or a manual emergency stop. 9. Consider the action when operation is restarted after an emergency stop or abnormal stop.
Also perform periodic maintenance and confirm proper operation. 9. Ensure sufficient clearance for maintenance activities. When designing an application, be sure to allow sufficient clearance for maintenance and inspections.
Also perform periodic maintenance and confirm proper operation. 9. Ensure sufficient clearance for maintenance activities. When designing an application, be sure to allow sufficient clearance for maintenance and inspections.
Also perform periodic maintenance and confirm proper operation. 9. Ensure sufficient clearance for maintenance activities. When designing an application, be sure to allow sufficient clearance for maintenance and inspections.
Refer to pages 4-5-4 to 4-5-9 for external dimensions in mounting.