3 Port Solenoid Valve and V124(A) cannot be mounted to the same manifold.
To release residual pressure, select a model with a back flow mechanism.
Air filter (5m or less) When using a solenoid valve, use a metal seal type (series VQ, VQZ, SQ, etc.).
Dont use a wrench on push-to-connect end. 2 2 Cut tubing square with a clean 90 edge Dont use excessive tube angle cut which can lead to leakage or breaking. 90 90 3 3 Use SMC Tube Cutters Dont use dikes, a knife, a saw or a dull tool to cut the tubing.
the tube surface of a closely mounted built-in strong magnet type cylinder by 30 mm or more. 3) When a built-in strong magnet type cylinder and a cylinder with a general-purpose auto switch are closely positioned, separate the cylinder tubes 50 mm or more. 4) Separate a general-purpose auto switch from the tube surface of a closely mounted built-in strong magnet cylinder by 50 mm or more
D-F9WV D-F8 Model A B C D E A B C D E A B C D E A B C D E A B C D E A B C D E A B C D E A B C D E 18.5 31 6.5 20.5 41 8.5 20.5 33 4.5 17 20.5 31 4.5 15 20.5 41 4.5 15 20.5 51 4.5 35 22.5 43 6.5 27 22.5 33 6.5 17 22.5 43 6.5 27 22.5 53 6.5 37 MIW12-12D MIW20-20D 6 4 4 2 18.5 29 6.5 20.5 31 8.5 MIS12-10D MIS20-10D 4 2 6 4 2.5 4 18.5 39 6.5 20.5 41 8.5 MIS12-20D MIS20-20D 6 4
Series 25 19 dB (A) Page 5-10-4 VEX AN101-01 AN110-01 AN120-M5 AN120-M3 BC sintered body type Ideal for the exhaust of a compact valve or pilot air. 16 dB (A) 21 dB (A) 18 dB (A) 13 dB (A) 100 m AN Page 5-10-5 Silencers Exhaust Cleaner 70 m AMC One-touch fitting connection type Can connect with One-touch fitting directly. 25 dB (A) 30 dB (A) It differs depending upon the model.
A B C A B A B A B A B 15A 20A 25A Note 1) For each piping diameter for each body size, the second and later numbers or symbols indicate reducing.
SGH(A)32-7020 SGH(A)42-7025 SGH(A)13-3010 SGH(A)23-3015 SGH(A)33-3020 SGH(A)43-3025 SGH(A)13-7010 SGH(A)23-7015 SGH(A)33-7020 SGH(A)43-7025 3/8 7.5 42 (1.8) 1.4 1.5 1/2 9.4 65 (2.7) 2.4 2.6 7 MPa 2-port 3/4 12.4 112 (4.7) 4.7 5.3 1 15.4 155 (6.5) 6.6 7.2 3/8 9.4 50 (2.1) 56 (2.3) 1.6 1.7 11 1/2 10.5 55 (2.3) 73 (3.0) 1.6 1.7 3 MPa 15 3/4 12 90 (3.8) 92 (3.8) 2.6 2.8 17 1 15.2 135
MGPM MGPL/A MGPM MGPL/A MGPM MGPL/A MGPM MGPL/A MGPM MGPL/A MGPM MGPL/A MGPM MGPL/A MGPM MGPL/A MGPM MGPL/A 12 16 20 25 32 40 50 63 80 100 (1Nm = 0.74 ftlb) 5 Compact Guide Cylinder Series MGP High Precision Ball Bushing/MGPA Non-rotating Accuracy of Plate Caution + Positioning accuracy for pin hole on the plate Dispersion of dimensions when machining each component will be accumulated in
When very clean air is required, install a separator as mentioned above on the downstream side, or instead of a regulator, use the order made specification (refer to page 35) fitted with a micro mist separator regulator (series AWD). 3.
10 A 180/200 W 50/60 Hz 220 W 0.01 m (99.9% filtration efficiency) Particles of 0.3 m or more: 3.5 particles/L [ANR] or less Heater operation, PID control Singlephase 200 VAC (50/60 Hz) 2.1 A 5 A Singlephase 230 VAC (50/60 Hz) 2.1 A 5 A Singlephase 100 VAC (50/60 Hz) 9.4 A 15 A Singlephase 200 VAC (50/60 Hz) 4.8 A 10 A Singlephase 230 VAC (50/60 Hz) 4.8 A 10 A Power supply Note 4) Operating
To use a perfect valve and a spacer style regulator, use a manifold or a sub plate as the standard and stack in the following order: the perfect spacer, spacer style regulator, and the valve.
Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Caution: Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Warning: Danger : Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury.
To release residual pressure, select a model with a back flow mechanism.
[Check valve] A check valve is a safety device intended to prevent reverse flow. The AP 64 is a unique design with only one moving part in the gas stream, an O-ring. It is a springless design, free of springs and poppets. [Vacuum generator] A venturi device that creates vacuum by flowing gas through a nozzle.
When a surge generating a load such as a relay or solenoid is directly driven, use a type of switch with a built-in surge absorbing element. 4. Since the type of fluid varies depending on the product, be sure to verify the specifications. The switches do not have an explosion proof rating. To prevent a possible fire hazard, do not use with flammable gases or fluids. 5.
To release residual pressure, select a model with a back flow mechanism.